Jump to content
SAU Community

Work Xd9 18x10 +18 R32 Gtr Users

marksuxass

By marksuxass,
in Exterior & Interior Styling

 Share

Recommended Posts

marksuxass Collaborator

marksuxass

Posted
Posted

Recently bought a set of work xd9s in 18x10 with a +18 offset. They havent been fitted to the car yet as its still in peices and waiting for paint. What i need to know is do these go on with out any mods, and will i need to stretch tyres maybe?

Link to comment
Share on other sites
marksuxass Collaborator

marksuxass

Posted
  • Author
Posted
33 and 34 should be ok

not sure about a 32, think your going to have a little bit of an issue

thats the same offset /size 18/10/18 as i had on my NTO3s on the 34

why dont you just test fit one?

i havent ordered any tyres for it yet, i test fitted them on with the car off the ground, sticks out the guards a little, but i spose the car was unladen. Ive seen a few r32 gtrs with the same sized wheels, but unsure if any mods where done to get them on there

Link to comment
Share on other sites
johnbarry88 Grand Master

johnbarry88

Posted
Posted

I had them on my 32 gtr with 235 tyres, only cuz that is what you could legally run on them in QLD and they stuck out 5-7 mm on standard suspension. So with some 265's and some lower suspension you should get away without flaring the guards, that if the guards havent been repaired for some reason in the past.

Link to comment
Share on other sites
TURBZ Enthusiast

TURBZ

Posted
Posted

I'm in the same position at the moment with XD9's and looking at using a 265/35, would prefer not to roll the guards..

Here's a few from rimtuck.com without guard mods.

18x10+16 with a 275/35, -3 front camber and -1.5 rear camber and no guard mods.

http://www.rimtuck.com/setup.php?id=325

18x10+20 with a 265/35, -1.5 and -2 camber and no guard mods.

http://www.rimtuck.com/setup.php?id=322

When I first bought the car it had r34 gt-r rims with a 275/35, was going to add a 10mm spacer all round and it would of just cleared the guards. I checked the XD9's with a 265/35 against the old rims on a fitment calculator and it said the only difference is that the XD9's will stick out 7mm more.. I'm going to trial fit a tyre just to be safe before I buy a set anyway.

Here's the calculator

http://www.rimsntires.com/rt_specs.jsp?item=Wheel-Tire

Link to comment
Share on other sites
Beelzebub89 Grand Master

Beelzebub89

Posted
Posted

I run 263/35/18s on my XD9s the same size. You will need to get your guards rolled. I had them without the guards rolled and standard suspension and they used to scrub in the rears. Rolled guards and stiffer suspension has sorted out all my scrubbing issues.

Link to comment
Share on other sites
marksuxass Collaborator

marksuxass

Posted
  • Author
Posted
im runing same wheel with 245/35/18 my gaurds are rolled, no clearance issues at all, goin to go 255 or 265 for my next set.

Is that both front and rear guards rolled? or did you get away with just rolling the rears?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Does anyone know whats happening with harness on drivers door?

      By GTSBoy · Posted

      The two diagrams are equivalent. The R32 one is just one sheet out of about 3 showing everything in the whole car all at once. And without knowing the functionality that occurs in the modules, they are both equally opaque.
    • Neostead2000
      R35 OEM Injector dead times

      By Neostead2000 · Posted

      8v - 2.48ms 9v - 2.15ms 10v - 1.74ms 11v - 1.41ms 12v - 1.15ms 13v - 0.99ms 14v - 0.89ms 15v - 0.82ms 16v - 0.81ms I'm running these values on my RB20 Neo with 570cc Denso R35 stock jets and it's great. Also bought a set for my Legnum VR4, love these injectors!
    • harambe34
      Does anyone know whats happening with harness on drivers door?

      By harambe34 · Posted

      Thanks for your reply,  Those blue/green wires running to the actuator aren't attached to anything, so I'm not sure how the central locking is still working. I will have to take a good look tomorrow, I don't have the car with me. After googling it seems like a pretty common aftermarket actuator which even uses the same green/blue wires the immobiliser required. i'll test everything tomorrow and if it's working i'll melt the solder, strip it, resolder and neaten it all up with some heat shrink. I don't have to understand it if it works hahaha I just don't want a fire/ short circuit. That R32 diagram looks more like a continuity chart? Can you make sense of this form the R34 manual? 10V is probably due to very flat battery, i'll recheck as well tomorrow, I did have to jump start it haha. Thanks again!  
    • GTSBoy
      Does anyone know whats happening with harness on drivers door?

      By GTSBoy · Posted

      So, COM doesn't mean comms. It means common. What common itself means will depend on the type of device. For a two directional actuator (ie, one that can push and pull on the same output rod) then the common will typically just be the earth connection. There will be at least 2 other wires. If you put 12V on one of the other wires, then the actuator will push. On the other 12V wire, it will pull. Can't quite make out what is going on with the wiring of your actuator. It appears to have several wires at the actuator plug, but there only appears to be 2 wires where its loom approaches the door control module, with at least one of the others cut off. I don't know these actuators off by heart. I'd have to look at a wiring diagram for one before knowing what the wires were about, and that's despite me having to replace one in my car not all that long ago. Just not interesting enough to have dedicated memory set aside for trivia like that any more. That actuator is an aftermarket one, not the original one, which probably died and was replaced. That might require some sort of bodge job on wiring to make it work. Although nothing should justify the bodginess of the bodge job done. As to the soldering job on the door module's loom plug. Ahhahhahaha. Yes, very nasty. Again, I cant tell you what any of those wires do. You'd need to study the R34 wiring diagram (if you can find one that shows the door module). I don't think I have any. I'd have to study the R32 diagram to start to understand what mine is doing, and again, even though I've had a problem with mine for the last 25 years (where it locks the passenger door when the driver's window reaches top or bottom of travel) I'm just not interested enough to try to to work it out. So long as it's not burning down, it's fine with me. Here's the R32 GTR diagram, which, confusingly, has rear door lock actuators and window motors on it!! As you can see, unless you understand the functions of the door lock timer and the power window amplifier, you'll never be able to work out how it works just from the diagram. I don't imagine that the R34 one is any better. Hopefully an R34 aware bod can help. FWIW, the two wires that are cut and joined look like they are both power supply - so hopefully it is not fatal to join them. The 10V you measured on the cut off free end of one of them is concerning. You'd expect 12V, and it might be the reason for the bodge job joining them together.
    • harambe34
      Does anyone know whats happening with harness on drivers door?

      By harambe34 · Posted

      Oops my bad, here you go .
×
×
  • Create New...