Jump to content
SAU Community

R32 Gts-t Track Car Stripped With Loads Of Gtr Parts.


Recommended Posts

I have the following R32 GTS-T specific parts

Fully adjustable suspension. Height, dampener and cones with 3 pairs of springs 4,6 & 8 Kg’s 500km old $500

Nismo rear strut brace $100

Front strut brace with brake master cylinder stopper $100

Nismo original plastic rear pods $ 100

Rear wing like a GTR $120

Steering rack with tie rods $70

Drive shaft $40

Head lights and blinkers L&R $150

Brake master cylinder $90

5 Stud Hubs $90 each side

Lower control arms $25 each

Bottom door trims $20 pair

Radiator 25mm $50

RB20 turbo $30

Conversion spacer studs to allow GTR rotors and calipers to fit GTS-T $50

Clutch Fan fits all RB’s$40

Any questions please post up or PM. Ta

For anyone looking to do a manual conversion to their GTS-T!

Gear box $100

Clutch master and slave & piping $100

The following parts are R32 GTR which are an upgrade that fit an R32 GTS-T

3 “ full exhaust with GTS-T turbo header pipe $140

2way Mechanical Diff 4.2, hub to hub with cradle $600

Full oil cooler kit, 300mm x 250mm x 50mm cooler, with sandwich plate and remote filter and oil temp gauge and all hoses $400

FMIC 75mm thick, 600mm x 300mm with piping to engine bay R32 GTS-T will need inlet pipe $140

Adjustable front Caster Rods $ 90

Adjustable front camber arms $120

Rear Calipers $ 70

Rear rotors $50

Front calipers with various meaty pads $120

NEW unused Ferodro DS2500 pads $180 (New $260)

DBA veined rotors 500km old just machined $200

Fuel tank $180

Fuel pump $140

Front seat with small tear’s $ 90

Black aluminum bonnet that needs a small repair $80

Radiator 20mm $90

Pickup from Castle Hill, Sydney prefered, please check Oz post for postage info at your cost.

I will post up separately but have the following also.

3lt engine rebuilt with forged CP pistons and rings, with a serviced GTR head, GTR inlet manifold and single turbo manifold for T04Z, not used and on engine stand.

R34 GTR original wheels currently being re-sprayed.

Set of 4 x white 17 x 8” and 17 x 9” 35mm offset jap racing wheels with worn Dunlop D02 on them.

Pair of 18 x 11” with 295 semi’s and a spare set of Porsche cup 270 slicks.

Pair 18 x 9.5” with Porsche cup slicks.

post-42-1289728318_thumb.jpg

post-42-1289728327_thumb.jpg

post-42-1289728337_thumb.jpg

post-42-1289728347_thumb.jpg

post-42-1289728356_thumb.jpg

post-42-1289728365_thumb.jpg

post-42-1289728377_thumb.jpg

post-42-1289728397_thumb.jpg

post-42-1289728411_thumb.jpg

post-42-1289728427_thumb.jpg

post-42-1289728441_thumb.jpg

post-42-1289728452_thumb.jpg

post-42-1289728462_thumb.jpg

post-42-1289728474_thumb.jpg

post-42-1289728482_thumb.jpg

post-42-1289728490_thumb.jpg

post-42-1289728498_thumb.jpg

post-42-1289728514_thumb.jpg

post-42-1289728522_thumb.jpg

post-42-1289728532_thumb.jpg

post-42-1289728559_thumb.jpg

post-42-1289728567_thumb.jpg

post-42-1289728579_thumb.jpg

post-42-1289728591_thumb.jpg

post-42-1289728601_thumb.jpg

post-42-1289728609_thumb.jpg

post-42-1289728618_thumb.jpg

post-42-1289728690_thumb.jpg

Link to comment
Share on other sites

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Hey mate keen for seat would u post? To Adelaide 5010

Sorry Hcr, it weighs way too much and postage will cost heaps and I have no way of packing it. If you have a contact in Sydney who can pick it up and do the postage your in luck otherwise sorry no go. :)

Link to comment
Share on other sites

Paul I'll take the rear calipers, rear rotors and the damaged bonnet.

I can pick up any night during the week that suits you

thanks brad

Brad,

Done , no probs. Im about any day but wednesday this week. Tomorrow night will be good for me, any time after 6pm. I will PM you my address now, just let me know what is good for you.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
    • Hello, I am looking to replace my two rear drive shafts in my R34 N/A Skyline but I'm finding conflicting information. Do S13/S14/S15 or R32 NA/ R33 NA fit? https://justjap.com/products/gsp-premium-rear-drive-shaft-l-h-nissan-silvia-s13-s14-s15-3x2-type?currency=AUD&srsltid=AfmBOoqY7EwDaYCUoUU3mxxZ_qrUXkVVHiV4MIN7ozoar6scjnEiekv- would this fit?
×
×
  • Create New...