Jump to content
SAU Community

2011 F1 Thread


zebra

Recommended Posts

Lol Webber sure is one tall poppy.

interesting to see how he performed so badly, historically its one of his worst performances, hell bounce back though, people under rate him but he's tough as f**ken nails.

Link to comment
Share on other sites

The theory on RBR is that they have a better aero package and weight distribution without KERS although it was speculated that they run a KERS lite which is available off the line for one use only but there was no sign of that today.

Captn Chin showed high tyre wear, no grip and a big gap to his team mate that just wasn't apparent from the earlier races of the 2010 season with the exception of the last race last year. Hard to understand why the setup was so far away unless there is a problem with the car.

Link to comment
Share on other sites

i thought that weeber got stuffed over by team stratergy just like final round last year. he came in and put hards on. that didnt work so no one elce put them on. he lost all his time from then and had to revert to med/soft and couldnt make the time back up

Vettol complained of the tyres going off at a simmilar time to mark and they brought mark in first. if you watch just this part of RBR im sure webber will always pit first and change compounds. this then detemins what vettol gets.

somthing to keep an eye on.

Link to comment
Share on other sites

i thought that weeber got stuffed over by team stratergy just like final round last year

Nah, Webber was harder on the tyres. Any strategy was rightly in SV's favour due to track position if any benefit went to him at all.

He was farked by the front right tyre change losing him around 3 seconds which probably cost him one place only.

Link to comment
Share on other sites

I have totally changed my tune. Ferrari should keep massa fir as long as humanly possible

With a backbone that weak and performances that horrible he'll be screwwing them out of WCC's for years

again, :rofl:

Link to comment
Share on other sites

Based on this weekends (admittedly limited) evidence, I have grave fears for anyone's ability to stop Vettel walking his 2nd drivers title, assuming the team can provide him with a car that finishes races most rounds this year.

Link to comment
Share on other sites

The one hd coverage was absolutely woeful today especially the post race press conference. They cut away halfway through Petrovs first question usually they show the three driveers answering a few things about the race and then go to the winner for another few questions.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...