Jump to content
SAU Community

Recommended Posts

Hey guys,

Just got my skyline yesterday, but while driving at night I noticed I couldnt see how fast I was going, nor at what rpm or anything else. The back part of the dash lights up green, but its not very bright at all, and the red pointer things dont light up at all ?

I dont have a dimmer switch, looks like the workshop didnt fit them.

I've taken the dash apart, but I really have no idea what to do.

Any ideas ?

Thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/34462-my-dash-lights-are-really-dark/
Share on other sites

The right hand stalk itself only has the parking lights, low beam, high beam options. No dimmer switch on there.

Ive checked everything, pulled the whole dash apart, and nothing - no dimmer ;)

Are the red thingies which indicate which speed you're goin at, rpm, etc, meant to light up ?

Coz mine dont come on AT ALL (i dont think ?) Or if they do, theyre really dark

I havent checked the fuse

But then the back of the dash lights up green, albeit a very poorly illuminated green, so I dont THINK its the fuse.

Keep the ideas coming though ;)

Id probably just need to find the right wire for the power/illumination to the dash, and rewire it with a different impedance ?

Although I really dont wanna do that in case i f u k things up

:)

Cheers

the dimmer in R33 is fitted on compliance. if you don't have one, the compliancer must be a bit dodgy. check the bulbs behind the dash (need to take it apart) could be one of those aftermarket bulbs with coloured bulbs or even coloured rubber sleeves on.

i always thought that they came standard on 33's well 95 and upwards anyways.

and the dimmer switch thingy should be on the left hand side under the wiper stick right next to 3 small rectangular holes used for climate control not the right. well mine is anways.;):D

I think i'll just leave it at - my compliancer is dodgy :headspin:

No dimmer switch anywhere to be found. Trust me on this one.

rs73 - I noticed that the bulbs had green 'condoms' over them. When the dash lights up, its dark green. What colour is it meant to be normally ?

Thanks for all the help so far guys ;)

Tom

In mine it has a blue 'condoms' which makes the lights turn a bit towards white when it's on.... that's a standard one. I've seen someone fitted with a painted one. Depends what paint, sometimes it's so bad that it didn't transmit enough light. the stock rubber condoms will be transparent enough so you can see the dials properly. You can try taking them off and see if it's not too bright or too yellow for you.

Yes. There's various bulbs behind the speedo face that's been positioned on "strategic" location, so that it can illuminate evenly even the needles as well. The needles are like transparent plastic that will somewhat "glow" when being backlighted. You might find yours do when you take that green 'condoms' off....

Ok what you need to do is go down to Supercrap autos or Autobarn and buy some 5watt wedge type globes. They are also known as parker globes. The standard ones are dim at 3.8 watts.

Take your dash cluster out and replace the bulbs with the 5 watt types. Make sure you do use the blue covers on them as it makes the light more "white" as opposed to orangy yellow crap the wedge bulbs emit.

There are some brands of whiter brighter globes available like Phillips blue vision parkers but I dont know where to buy these.

If this doesnt help there is a fault somewhere.

All fixed

I havent checked to see the colour of the globes - they look a bit yellowish.

But theres definitely light illuminating the dials, which is all I really need

If I get bored of this ill either get covers for the globes or go EL

Cheers guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
×
×
  • Create New...