Jump to content
SAU Community

Limit Of 2 X 044's On E85

Piggaz

By Piggaz,
in Engines & Forced Induction

 Share

Recommended Posts

Piggaz Grand Master

Piggaz

Posted
Posted

Hey guys. Steve (N1 GTR) and I were discussing this today while we were running the lines to my surge tank. I understand not many people will be able to answer this as it is a shitload of power but, does anyone know the limit of 2 X bosch 044's on E85?

We are both running very similar setups.... although I am a 2.8 and Steve is a 3.0 litre. Same cams and turbo's. Steve is currently making 455 RWKW at 24 psi.... My car will be on the dyno tomorrow and Friday shoving 2 bar down its throat and hopefully making 500 rwkw +..... if the pumps can flow that much. Will be interestng either way.

Link to comment
https://www.sau.com.au/forums/topic/344654-limit-of-2-x-044s-on-e85/
Share on other sites
  • Replies 113
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

HYPED6 Collaborator

HYPED6

Posted
Posted
Hey guys. Steve (N1 GTR) and I were discussing this today while we were running the lines to my surge tank. I understand not many people will be able to answer this as it is a shitload of power but, does anyone know the limit of 2 X bosch 044's on E85?

We are both running very similar setups.... although I am a 2.8 and Steve is a 3.0 litre. Same cams and turbo's. Steve is currently making 455 RWKW at 24 psi.... My car will be on the dyno tomorrow and Friday shoving 2 bar down its throat and hopefully making 500 rwkw +..... if the pumps can flow that much. Will be interestng either way.

There are too many variables. One is Voltage. 044's do pump quite a bit more the better the voltage in a 12-15 volt system.

Another is how long you need to generate that power for. Sounds funny but think of it this way.

2 x 044's at 40 psi will flow around 7 Liters a min. Say your surge tank is 3 liters and your in tank pump can flow 3 liters a min at 0 psi.

Now say your 1600cc injectors are at 75% duty. So thats 1200cc per cylinder and 7.2 (7200cc) liters a min is being consumed.

Now, Hold your engine flat for 10 seconds or an average power run.

So your engine will consume 1.2 Liters from your surge tank. Would have returned nothing from the fuel system but your in tank has supplied 500cc of fuel.

Now hold your engine flat for 40 seconds.

You will consume 4.8 liters of fuel. Again nothing is being returned from your rail. Your in tank pump has supplied 2 liters soo all up you have had 5 liters if fuel available and only used 4.8........

Now hold it flat for a minute.

HYPED6 Collaborator

HYPED6

Posted
Posted

A real world example.

I ran these numbers on an engine we where doing development on. 2.5 6 cylinder.

Had 2 x 044 and a 3 liter surge tank. Wasn't even making 600rwhp through an auto and we where running 30% Meth and 70% 98.

The engine was tuned to perfection on the dyno. Even as far as Indervidual cylinder EGT's so we knew where weren't going to melt anything.

Now I wish I had have run the numbers earlier because the thing made it 380 meters of a 400 meter drag run and melted 2 pistons.

We now have a 20 liter surge tank and 3 x 044's

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted

Yeah fair call.

Both surges are are about 5 litres. Nismo pump feeding both i think (well mine atleast). Now thats not exacatly under pressure like it in feeding the engine... so in theory it should be able to flow more. Injectors are ID 2000's but really i shouldnt be any higher then 60% duty (but hey i could be proved wrong)

So 60% of 2000 is 1.2 x 6 = 7.2 litres a minute.

Steve and I sorta had a play around with figures today. We came up with 518 RWKW. Obviously that is VERY rough but I think both of us are going to be touch and go with 2 pumps. Stupid E85 and its mega thirst!

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted
A real world example.

I ran these numbers on an engine we where doing development on. 2.5 6 cylinder.

Had 2 x 044 and a 3 liter surge tank. Wasn't even making 600rwhp through an auto and we where running 30% Meth and 70% 98.

The engine was tuned to perfection on the dyno. Even as far as Indervidual cylinder EGT's so we knew where weren't going to melt anything.

Now I wish I had have run the numbers earlier because the thing made it 380 meters of a 400 meter drag run and melted 2 pistons.

We now have a 20 liter surge tank and 3 x 044's

That is not good news! I got no room for a 3rd pump dammit!

N1GTR Grand Master

N1GTR

Posted
Posted

Hyped6 we both have id2000's, twin 044's have their own lines direct to the fuel rail (no stupid y pieces here), Paul has a NISMO lift pump but I've got another 044 intank

We didn't check voltage today, we had no time. I'd like to know what voltage mine runs at now!

HYPED6 Collaborator

HYPED6

Posted
Posted
Yeah fair call.

Both surges are are about 5 litres. Nismo pump feeding both i think (well mine atleast). Now thats not exacatly under pressure like it in feeding the engine... so in theory it should be able to flow more. Injectors are ID 2000's but really i shouldnt be any higher then 60% duty (but hey i could be proved wrong)

So 60% of 2000 is 1.2 x 6 = 7.2 litres a minute.

Steve and I sorta had a play around with figures today. We came up with 518 RWKW. Obviously that is VERY rough but I think both of us are going to be touch and go with 2 pumps. Stupid E85 and its mega thirst!

I have found E85 Not that bad. Yes you use a lot, but EGT's are much lower and really to get the most out of it you need to be measuring them.

Think 3025 35r, 24 psi on 98 Lambda of 0.78 EGT's nudging 800c Around 490rwhp

Same engine 24psi E85 0.8 Lambda EGT's 700c 520 rwhp

Then we lean it out, 0.85, 0.9, 0.95 where we ended up. EGT's 770c Measured at the Hottest cylinder 560rwhp

Going from 0.78 to 0.95 made the fuel usage not to bad. But defiantly need EGT's to get the best out of it.

HYPED6 Collaborator

HYPED6

Posted
Posted
Hyped6 we both have id2000's, twin 044's have their own lines direct to the fuel rail (no stupid y pieces here), Paul has a NISMO lift pump but I've got another 044 intank

We didn't check voltage today, we had no time. I'd like to know what voltage mine runs at now!

Just drop your return line off your reg and run into a measuring container. Start your engine and wait 15 sec.

Thats the best way to measure how much flow you have at system voltage.

But you also have to remember, as pressuer increases flow decreases. So as your 1:1 reg starts working your fuel pump flow will decrease.

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted
Hyped6 we both have id2000's, twin 044's have their own lines direct to the fuel rail (no stupid y pieces here), Paul has a NISMO lift pump but I've got another 044 intank

We didn't check voltage today, we had no time. I'd like to know what voltage mine runs at now!

We will chuck a multimetre at the pumps tomorrow before we leave mine. Being directly off the battery it should be whatever that is!

N1GTR Grand Master

N1GTR

Posted
Posted
Just drop your return line off your reg and run into a measuring container. Start your engine and wait 15 sec.

Thats the best way to measure how much flow you have at system voltage.

But you also have to remember, as pressuer increases flow decreases. So as your 1:1 reg starts working your fuel pump flow will decrease.

Will do when it's back at the tuners ;)

I'm not sure if the lift pump is setup properly through the ecu (autronic sm4), but say the lift pump 044 is turned up to max flow under WOT, what sort of flow is that going to see into the surge tank?

Neither of us are hard into drag racing, but I see your point about the size of the surge tank. If either of us held it flat for 1minute we would be in jail. On a circuit day the longest WOT is eastern creek straight, at the drags (we will both get booted after one run) but that will be over much quicker than the ec straight. Which makes me think of time to fill the tank back up for example we go WOT down a straight for 30 seconds, then brakes, then back on throttle. What sort of flow will the surge tank take during the braking time (I know this isn't easy at all)

N1GTR Grand Master

N1GTR

Posted
Posted
We will chuck a multimetre at the pumps tomorrow before we leave mine. Being directly off the battery it should be whatever that is!

Doh, forgot what equipment you have there from work

Might have to borrow it for mine next week

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted
I'm good at sitting and watching, as you saw today :down:

Plug it in and I'll watch it

LOL. No comment. ;)

Doh, forgot what equipment you have there from work

Might have to borrow it for mine next week

Yeah mate. Take it anytime you want. Its mine so yeah whatever.

The Nismo intank pump flows 4.6L/min at 3.0kg/cm2.. BUT it wont be at 3bar (close enough) so it shuld flow more. It would be nice to have 2 pumps lifting to the surge but really I think thats overkill. Might be a question for Rob from RIPS? He would know. That bloke is a nutter!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Yousif alhaydari
      WTB OR BORROW r33 stock gtst exhaust

      By Yousif alhaydari · Posted

      Hi guys looking for a r33 Gtst stock exhaust asap in Melbourne have $$ waiting thanks 
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Always have 😁
    • luke gtr
      So i brought a boat...

      By luke gtr · Posted

      Jump into the wasteland. Plenty of random posting/chatting going on in there.
    • OST Micah
      RH9 R32 GTR Build Thread

      By OST Micah · Posted

      I did not go to GTR Festival. It's quite a long drive and the car wasn't dialed in yet. I also wanted to see how the racing portion went before going. From what I can tell the classes were not heads up, index, or bracket - just whoever has the quickest ET wins. Never heard of that sort of thing before and maybe some people like it but it's not my cup of tea. I don't suspect I'll go if that is how the racing is done. I did get the car out three times and had issues each time. Some were my error - haven't raced the car in over two years - and others were parts. Had trouble getting the clutch to slip correctly and remembering how it was set up in the Haltech. Broke some drivetrain parts as well that couldn't be fixed in a couple days to get back out. Season definitely didn't end the way I wanted but at least the bearings are still fine! Not a fleck of material in the filter. Really hoping next year is the year I can actually test this car properly. 
    • MBS206
      HY51 Fuga Hybrid

      By MBS206 · Posted

      find it funny everyone claims different fuel chains, do different things with their fuel blah blah blah. We don't have that many fuel terminals in Australia. The fuel tanker trucks drive into the terminal, fill up, and drive directly to the service station and dump out. The majority of fuel you get, is coming out of the same terminals. The variation is actually at the individual service stations and how good their tanks are, as well as how much turn over they actually have. Older fuel stations, that haven't had their tanks replaced are going to end up with the worst fuel. Also a lot of older stations have shit design, and shit maintenance, and end up with more water absorption into the tank. This is when you then get a bad batch of fuel. Other shit things happen, like tanker drivers have a f**k up, and starting to unload the wrong compartment on their truck into the wrong tank. 
×
×
  • Create New...