Jump to content
SAU Community

Hid Technical Question

strydes

By strydes,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

strydes Collaborator

strydes

Posted
Posted

Ok, so I've managed to get the old globe out, tweak the locking pin to fit around the HID globe, put the ignitor onto that and attach it to the ballast... but now I'm not 100% sure.

So there was a green and black cable running to the light itself, with what looks like the black one having the end cut off and changed to suit a screw in. So, I'm assuming I need cut that end off and change to suit the pin connector as per the first image. Can someone confirm for me?

Next question, the plugs that attach to the ballast, where do I need to solder these cables into?

I've scoured the net for close up pics of the back of the headlight which I'm sure will answer my question but no luck. Thanks in advance.

post-8519-1289996093_thumb.jpg

post-8519-1289996267_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/344670-hid-technical-question/
Share on other sites
V35_Paul Veteran

V35_Paul

Posted
Posted

Oh and give Alistair a call from Autoworx

Contact Details:

Phone: (08) 9409 2445

Fax: (08) 9409 2446

Address: 30 Automotive Dr, WANGARA W.A.

Email: [email protected]

http://www.autoworx.com.au/

He's does compliance on them so would know

strydes Collaborator

strydes

Posted
  • Author
Posted
quite simple . follow the two coloured wires back to where they were cut :)

the bulb already has power.

Thanks Chris, just to confirm... so solder the green and black to the orange wires of the plug?

That was my initial plan, but the pins on the back of the ignitor psyched me out.

  • 4 months later...
Pulp Veteran

Pulp

Posted
Posted

Hi guys!

I finally had a chance to remove my bumper and get the head light units out......... only to find that they cut away the ignitor :(

Good thing out of this little excercise was that the HID fog light kit I have installed only had their connectors disconnected from the balast units, so connected these and whola! they worked! nice :)

I'm going to phone around locally (Perth) and find out if I can source the harness quickly or at least the ignitor piece to fix up the headlights now.

I'd like to do this soon as I am think of selling the V.... yes that's right selling the V! :( I know what you are all thinking, pointless fixing up the HID, but I just feel like doing it out of fun and to say that I finally did it :)

Ok cheers guys!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
    • kevboost7
      Magnetic Drain Plug Snapped in Half

      By kevboost7 · Posted

      F my life. I was changing the oil on my R32 GTR today as usual and ran into a bit of a snag. I drained the oil out and was getting ready to finish the job by tightening the drain plug, however The stupid magnetic oil drain plug snapped in half, right at the magnet part. After about an hour of trying to remove it, I used a drill bit, which unfortunately pushed the magnet all the way into the pan, and just leaving the hollow threaded part of the bolt remaining. I was able to remove the hollow portion of the bolt from the oil pan with some pliers but the magnet is still in there.  So, the question is, should I drop the oil pan to get the magnet piece out, or is it okay to leave it in there? I really dont want to drop the pan, i'm about to go nuts.  PSA: Do NOT buy a BLOX magnetic drain plug. This is the one i had.    https://bloxracing.com/products/magnetic-oil-drain-plug-m12x1-25mm?variant=37131252859052&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gad_source=1&gclid=CjwKCAjw47i_BhBTEiwAaJfPpgti1D2JwO7TDuMpXuqeQPCuIQSAfwxpWQH5rF9MD7sm5SCZDWLR_RoC_YoQAvD_BwE    
    • 25debt
      MAJOR FUEL ISSUES 25det neo r32

      By 25debt · Posted

      I actually have an aftermarket hanger, the detschwerks x1 hanger, but my dw420 has never really sat in it correctly, good to know I can just modify it a bit to suit. Yeah cheers man will definitely have a play with it and hope it solves my dramas.
×
×
  • Create New...