Jump to content
SAU Community

Recommended Posts

I hope for some suggestions, or maybe even a referral to someone who may know wtf is going on. Short story is made a stack of mods, twins, z32s, fc, inj, pump, cams, reg, splitfires, cooler, etc. car was tuned, started perfectly, but was very disappointing in the top end.

So i had the car re-tuned by another dude with 1000cc ID's and removed the resistor pack. Tune is awesome, good on fuel, smooth idle, very linear power delivery, and decent final figure. However the startup is now crap. Cold start is quite good, also when you turn the car off and on again within 5 minutes. The problem is when i park the car for anything between 30mins to 6hrs and try start it again. It cranks forever (30+ secs), i have to pump the accelerator, and just barely starts and struggles to get up to normal idle.

To the tuner's credit, he has spent hours on it, involving an electrical engineer and can't crack it... Injectors have been flow tested, voltage tested, pump has been tested, crank signal shows on the fc controller when cranking, plus heaps of other stuff. The tuner is a champion and has probably tuned most sydney cars on this forum, so i don't think for a second it is down to his ability, has to be some weird ass quirk...

PLEASE HELP!!!

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/
Share on other sites

I hope for some suggestions, or maybe even a referral to someone who may know wtf is going on. Short story is made a stack of mods, twins, z32s, fc, inj, pump, cams, reg, splitfires, cooler, etc. car was tuned, started perfectly, but was very disappointing in the top end.

So i had the car re-tuned by another dude with 1000cc ID's and removed the resistor pack. Tune is awesome, good on fuel, smooth idle, very linear power delivery, and decent final figure. However the startup is now crap. Cold start is quite good, also when you turn the car off and on again within 5 minutes. The problem is when i park the car for anything between 30mins to 6hrs and try start it again. It cranks forever (30+ secs), i have to pump the accelerator, and just barely starts and struggles to get up to normal idle.

To the tuner's credit, he has spent hours on it, involving an electrical engineer and can't crack it... Injectors have been flow tested, voltage tested, pump has been tested, crank signal shows on the fc controller when cranking, plus heaps of other stuff. The tuner is a champion and has probably tuned most sydney cars on this forum, so i don't think for a second it is down to his ability, has to be some weird ass quirk...

PLEASE HELP!!!

If your having to hold your foot to the floor to get it started i think you might be using the flood control of the power FC which means you are getting to much fuel while cranking use your hand controller to trim this, I had this exact problem with my GTR and playing with the hand controller fixed it.

Goodluck.

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5555658
Share on other sites

If your having to hold your foot to the floor to get it started i think you might be using the flood control of the power FC which means you are getting to much fuel while cranking use your hand controller to trim this, I had this exact problem with my GTR and playing with the hand controller fixed it.

Goodluck.

Thanks for the feedback mate. I haven't held it flat to the floor, but i have been pumping it for like 30-45sec to get it to start... I will try holding it flat and see if starts quicker, if so, than maybe it is too much fuel.

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5555708
Share on other sites

My car is the exact opposite!

Every morning or if the car has sat for a long time, its a B**th to start. I have to turn the key one shot. If i leave it in ignition till the fuel pump runs and cuts out, i have to crank it really long and depress teh gas pedal. but once it has warmed up or even after a few hours of sitting its starts like a charm. It only does this when it sits for too long like in the mornings or in the evenings after work. Anything i can do to solve this? Fuel pressure too high?

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5555843
Share on other sites

No smoke... U guys have nailed it, on first impressions. 4 starts so far, and every one of them a winner with foot flat to the floor!

What is odd about this is that the tuner tried leaning it right out and adding heaps more fuel, both ends of the scale with no luck. He and an electrical engineer went right over the car for like 5hrs and found nothing helped. He is prob the best known tuner on this forum too, so he is definitely no rookie...

Thanks guys, i will take this idea back to him.

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5557327
Share on other sites

I had a similar problem with my R32 and turned out to be fuel pressure was too high, try adjusting ur fuel pressure regulator

if u have a fuel pressure gauge on it, if not take it to somone who can. On my car when the ignition is turned on

it is running 50psi. starts up after a single turn of the key everytime..

Hope that helps in some way

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5567640
Share on other sites

What timing is it running at start?

The reason it is starting with some throttle is possibly die to the throttle allowing more air to enter the combustion chamber, which implies too much fuel while starting. Have you looked at any form of temperature correction in the maps (don't know about PFC, but Wolf has a seperate temp compensation map).

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5568153
Share on other sites

  • 2 months later...

Hey guys, digging out an old thread, i forgot to check back on this...

It is running BP98 now, no E85 as yet.

I don't believe the PFC has a temp compensation map, but i could be wrong...

Trent, i will forward through my map as soon as i can download it.

Link to comment
https://www.sau.com.au/forums/topic/344702-bch-wont-start/#findComment-5669701
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...