Jump to content
SAU Community

Recommended Posts

Guys i've been trying for 3 days getting the HICAS system off for the replacement of the ISC HICAS lock bar. I've managed to crack one side of the tie rods (with the square nut) and the other one is damn impossible. I've tried using a spanner to hold down the flat parts of the little metal rod inside the HICAS but it's not strong enough and i'm slowly rounding it. Anyone got tips and tricks to share please?

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/
Share on other sites

Try grab one side with bench grip or something. That would be easier. When I was doing mine I didn't have the bench grip so I pulled the whole thing

out with the help of my brother hold the steering rack on the ground, use a big shifter and him holding the shifter in place, and kick the shifter really hard :). The impact would make it easier to crack.

Hope this helps, where about are you in SE ?

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559467
Share on other sites

Hey mate thanks for being the first to reply. I'm located in Dandenong area. Very close to giving up :) it's taking all my time.

I've tried those metal vice grips ( http://vetquip.com/products/Orthopaedic%20...Grip%2020cm.gif ) + a spanner to hold it in place since it's kinda rounded off. Too slippery as well. The HICAS unit has been remounted with the 2 bolts so i didn't need to hold it.

When people say shifter, does that mean a spanner?

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559628
Share on other sites

Shifter means the adjustable open end spanner, I can come and give you a hand if you need, just pm me :)

I remember disconnecting those tie rod was doing my head in as well... you are not alone !

I live in Noble Park. Not that far away from you.

Edited by Panko
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559694
Share on other sites

boostn1099: tried WD40 (RP7 to be exact). Didn't need breaker bar to crack the first one so I don't think it's necessary. I still bit the dust lol.

Panko: Sure bro, when are you usually free? This won't go unrewarded. Also yeah i've been using 2 shifters then...trying...

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559704
Share on other sites

If you get a good enough grip on the nut with the tool, you can then use a low scissor jack to push/move the tool to break the probably rusted/seized contact/threads of the bolt. Or a breaker bar/bar extension etc but i would prefer using the scissor jack to move the tool as it will have alot more control - you are under a car after all. Have fun

Edit - and wd40 that sucker like mentioned above.

Edited by Touge Kyousou
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5563755
Share on other sites

i remember doing mine, and they were a bitch too.

as long as the hicas is still bolted in place, just get a nice tight spanner onto the nut (or vice grips if the nut is fcked), and then tap the spanner with a hammer in the direction you need to loosen it. The shock from the hit (maybe a few hits) usually helps crack the seal. it worked for me.

and remember this when you're doing your camber arms :blink: you'll need it!

oh yeah, and wd40!! as mentioned above

Edited by Munkyb0y
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5563804
Share on other sites

a tool worth trying would be a stilson. plumbers use them. as you push on the handle it tightens the grip of it. they are a bit bulky though so you need a bit of room around the bolt/nut in question. i have found them handy in the past.

stilson:

stilson_wrench_36.jpg

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5565531
Share on other sites

The thing is i'm not having troubles with loosening the bolt, i'm having trouble with the darn grip on the bolt. Have tried the spanner and hammer a few times but the whole unit just keeps turning guess i'll try some more. Will also try the stilson, thanks guys much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5567051
Share on other sites

  • 2 weeks later...

Guys sorry it's me again. Tried using stilsons, can't get a proper grip on the mildly rounded nut as there isn't enough surface area. Tried hammering the 4 sided nut, both by itself, and tightening the loosened nut and trying. Still can't get it loose. Don't know how you guys make it sound so easy. Called up R E Customs and they wanted $160 to remove the HICAS even though I had the bar already :thanks: I've tried so long already, it wouldn't be worth it if I had to pay that in the end...

This is becoming SOS. Please help.

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5579531
Share on other sites

If you have the space you can get a blow torch and heat the bolt up from the thread and try to remove it have done this a ton of times at work and works 99%of the time. if that doesn't work try welding a bolt onto the nut so you can hit the bolt welded to the nut with a hammer but once again only if you have enough room to do so . if you can weld a bolt to the nut be careful not to fuse the nut to the bolt that your trying to remove said nut from. hope any of this helps

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5579759
Share on other sites

Thing is I don't have any of those equipments let alone experience with them. I saw a post from a forum member who had welded a blob on the other side with the tie rod removed to get a proper grip on the damn thing. I would if I could...

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5579798
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...