Jump to content
SAU Community

Strange Sucking Noise

Deziner

By Deziner,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

Deziner Mentor

Deziner

Posted
Posted

Today my R33 GTR started making a weird sucking noise.

It has pod filters, but the sucking is not coming from them. The noise happens both while stationary (idleling) and also when driving.

It sounds like it is coming from the front of the engine bay but cant pin point it.

It dosnt get louder or quieter depending on speed/RPM's etc. is always sounds the same.

It sounds like a valve opening/closing and sucking air.

I have not done any work on the car since buying it so it has started out of the blue.

Any thoughts?

Link to comment
https://www.sau.com.au/forums/topic/345027-strange-sucking-noise/
Share on other sites
Deziner Mentor

Deziner

Posted
  • Author
Posted

Some more info that may help.

One of the belts was making a squeale on startup when cold, but would go away within 1 minute.

The morning the noise started the car backfired once but not after that.

Also the car still runs fine, both in gear and at idle, no hesitation no other starnge noises.

Timing belt was done not that long ago, maybe 8 months ago I believe.

Have searched this forum as well as other and Google and can not find anything similar.

Deziner Mentor

Deziner

Posted
  • Author
Posted

Started the car for the first time since the noise started, a couple things I noted.

The squeal that used to be there is still there but for a lot less longer.

Also, the noise didnt start immediately, it took about a minute or 2 of the engine idleing for it to start.

116.hks Community Regular

116.hks

Posted
Posted

Were the tensioner and idler bearings replaced when the timing belt was?

Your other squeal could be a strecthed belt, either alternator, a/c or power steering. If the were replaced at the same time as the timing belt they could have strecthed a couple of mm's.

Deziner Mentor

Deziner

Posted
  • Author
Posted
Were the tensioner and idler bearings replaced when the timing belt was?

Your other squeal could be a strecthed belt, either alternator, a/c or power steering. If the were replaced at the same time as the timing belt they could have strecthed a couple of mm's.

Not sure if any of the other parts were replaced when the timing belt was.

Would any of these lead to this sucking noise?

When I say sucking, that is what it sounds like, not sure if it is actually something sucking in air.

paulR32gtr Mentor

paulR32gtr

Posted
Posted
Just had a bit more of a look around.

I think it is coming from under the cover where the cam gears are. You can feel it kind of knock when you put your hand on it when it makes the noise.

Any ideas?

I would be very wary of starting the engine if there is knock coming from under there ;)

It's a bit painful but are you able to take the cam gear cover off and make sure the timing belt is looking ok? Very hard to diagnose over the internet but maybe a fraying timing belt whipping around might cause something like the sound you are describing.

I would be checking all the critical things first before proceeding.

Deziner Mentor

Deziner

Posted
  • Author
Posted
I would be very wary of starting the engine if there is knock coming from under there :P

It's a bit painful but are you able to take the cam gear cover off and make sure the timing belt is looking ok? Very hard to diagnose over the internet but maybe a fraying timing belt whipping around might cause something like the sound you are describing.

I would be checking all the critical things first before proceeding.

Yeah, I am very wary!!

I have not looked at taking the cover off and what is involved (i.e. do I need to take the radiator fan out etc.), not sure how hard or what tools are required.

I am pretty sure it is something to do with one of the belts. Like I said, I started last night because I wanted to see if it still made the squeal and it did but only for a second. Before it would squeal for a minute or so until it warmed up.

If the timing belt slipped, even a notch it would run the same correct? it still runs like it always has, just this noise!!

116.hks Community Regular

116.hks

Posted
Posted

The timing belt wont squeal. The squealling noise is 1 of the other belts. As ol mate said, take the top timing cover off and inspect the belt. If you can feel a knock from their, it's got to be inside. If you are not capable of doing it, i'd get a mechanic to do it before something goes really bad.

  • 3 weeks later...
Deziner Mentor

Deziner

Posted
  • Author
Posted

Well it turns out the car never had it's 100,000K service.

Workshop replaced the idler bearing (which was the culprit for the noise and mechanic said was missing half the ball bearing and he was surpised it was still spinning, also replcaed the tensioner, timing belt.

Radiator was also flushed and pressure tested, turned out to be 70% blocked.

While in the shop also had the boost restrictor removed and timing adjusted to suit BP Ultimate. Also had a service, all oils etc.

First Dyno result they did saw it making 230hp at all four wheels, end result was 288hp at all four wheels.

The car is stock except the pod filters and the removal of the boost restrictor.

They said it would have made 300hp at all fours but the stock fuel pump started to struggle.

Deziner Mentor

Deziner

Posted
  • Author
Posted

Sorry, that $1470 was for everything, not just the idler bearing. so it included:

Timing belt, idler bearing, tensioner, water pump.

Also included radiator flush, service (oils, oil filter) etc., removal of boost restrictor and adjustment of timing to suit BP Ultimate.

Included a couple Dyno runs as well.

Pretty good I think. Very happy with the result. Next will be upgraded turbos and exhaust system.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Getting lug nuts "gutentight" with no torque wrench

      By MBS206 · Posted

      Or get a guy in his early fiftys to do it. A single good "oof" and about two cracks from his lower back is about the right tightness...
    • GTSBoy
      Getting lug nuts "gutentight" with no torque wrench

      By GTSBoy · Posted

      It's impossible to convey what it will feel like to get the right torque. But you can develop a feel for it. A 900mm breaker bar is.....f**king huge. I only use a normal ~400mm one. But with 900mm being very nearly a metre, and the right torque being in the order of 100Nm, then you're going to need a bit over 100N of force, which is about 10 kg. So if you practice using the bar pulling up, instead of pushing down, then it will be about the same effort as lifting a 10kg bucket of water. That's what the pressure against your fingers should feel like. Ish. If you use a more typical length breaker, then it's about twice that. So a good 20 litre bucket, or a little bit more.
    • DraftySquash
      Getting lug nuts "gutentight" with no torque wrench

      By DraftySquash · Posted

      Also, if anyone has a torque wrench around Williams Landing area and can lend it to me for like 5 mins - I got 4 bottles of Furphy left and I’ll throw that in with a Happy meal 😂
    • DraftySquash
      Getting lug nuts "gutentight" with no torque wrench

      By DraftySquash · Posted

      So today I decided to bleed my brake fluid, which meant to the wheels came off the car at my garage for the first time. I only had a 90cm breaker bar with me and I noticed that some 1 or 2 lug nuts were a bit hard to get loose (from when the shop did the coilovers) Now.... when it came to putting them back on, I didn't want to put all my weight and overtighten them. So I hand tightened as much as possible and then put normal pressure on the edge of the breaker bar and tightened it until I couldn't turn it anymore without putting in an effort. Do you think that is tight enough? Or is that still too tight?  They are tighter than finger tight. Last thing I want is to have them strip or warp sh*t. But hard times mean I can't just go down to Supercheap and get a torque wrench 🥺
    • joshuaho96
      Coc or nox of nissan skyline

      By joshuaho96 · Posted

      Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
×
×
  • Create New...