Jump to content
SAU Community

New Speed Cameras Harbour Tunnel

mr moo

By mr moo,
in New South Wales

 Share

Recommended Posts

mr moo Veteran

mr moo

Posted
Posted

there are two speed cameras at the begining of the south bound harbour tunnel one is located at the toll gate and the other is 100m back where the old toll gates used to be. thought you may like to know.

Link to comment
https://www.sau.com.au/forums/topic/345221-new-speed-cameras-harbour-tunnel/
Share on other sites
FST513 Mentor

FST513

Posted
Posted

Wow... Like there wasn't enough speed cameras in sydney yet... Are you sure you didn't spot the bus lane camera (near the old toll gates)? If it isn't, then that is super gay!!!! Two within 100m...sigh.

mr moo Veteran

mr moo

Posted
  • Author
Posted

Nah def pointing towards the tunnel and i drive through the tunnel pretty much each day and they are def new. The bus lane is two lanes over and these cameras are right next too the left lane.

Cass: always a camera about 300m in from the start off the tunnel.

mr moo Veteran

mr moo

Posted
  • Author
Posted
Nah it's not the bus lane one.

It's a proper speed camera where the old toll gates were.

Its been there for ages now

Only been there for 3 weeks or so when i went on holidays on the 8/11/10 they where def not there. Them came back week and a half and they where there.

N1GTR Grand Master

N1GTR

Posted
Posted

If its the same ones im talking about, definatly have been there for quite some time.

Theyre on the left hand side as you do the tunnel, aiming where the old toll gates were, not too far from the bus lane cameras on the bridge lane

Regardless, anyone speeding through there is a dumbass - there's too many police and security cameras, not to mention other people.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Thanks Santa (the neverending trials of the 400,000klm, 400kw, RB30, manual swapped Stagea)

      By soviet_merlin · Posted

      Thanks Duncan! Yeah it's street use for me only. Maybe occasional track day. Any difference in noise when running with the two pumps? I would expect the lift pump to be more quiet than the main pump so hopefully not? And yes, unfortunately quite a big price difference to the simple hanger setup. Though I'm usually willing to trade money for better reliability and future-proofing. Buy once, cry once and all that. I'd be very happy to never have to deal with fuel pump / wiring issues again  
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
×
×
  • Create New...