Jump to content
SAU Community

What Is The Requirement To Import Car From Nsw To Adelaide


Recommended Posts

well I have recently purchased a V35 from melb. The procedure was... purchase the car, bring it back to adelaide, go to regency ID inspection centre (no need to book) and then fill out a simple form and wait to be assessed. This examination is not as strict as defect, but try to keep your car stock as possible. My v35 was stock, but they failed me for having tints. However I was able to pull out my tint in the car park and was passed shortly.

Once your car has passed, the inspector will allocate you with a form. This form is then taken to the actual regency department and you can purchase your rego.

For insurance, you may want to seek for a quote prior to purchase. I am with Justcars.

gl

beepee

Assuming the vehicle is registered interstate then you just need an ID check at either regency (as above) or lonsdale.

Fairly straight forward if the vehicle is pretty stock.

Thanks guys.really aprreciate it. What about the payment?

bpv35 : how much did justcars charge you for a year? Any quote for r34 gtr?

go onto the actual website and you're able to obtain a quote.

http://www.justcarinsurance.com.au/?cmpid=...04&2473PSEM

note: buy online is cheaper.

Edited by bpv35
  • 2 weeks later...

How much you paying for the one from NSW?

There is 34 GTR's local for sale :). I happen to have one with plenty of tasteful mods.

Also your not buying from an importer in NSW are you? And if u r i hope his name is not Eddie or any first name followed by Tran as a surname.

I brought my 1993 R33 gtst over from Sydney about 4 years ago

The ID check at regency is pretty painless they just had a quick look at the car, barely looked at the engine took under 30 minutes. But I did remove the aftermarket BOV and air filter before I took it there. The car had also been lowered and had illegally dark window tinting.

The guy tested the tinting and said it was too dark but he only recommended I remove it, I didn't remove it and still have it now 4 years later with no problems, they didnt mention anything about the height of the car. My mates said I was ok because the car is white and I was wearing a suit :happy:

Once the ID check is completed you go to the motor registration office where you get new licence plates and pay for your new registration plus stamp duty plus a fee for re registering the car. Because your car was most likely expensive you should check the stamp duty rate here:

http://www.revenuesa.sa.gov.au/index.html?http://www.revenuesa.sa.gov.au/stamps/stampd.html

It cost me at least $500 to register and transfer my car.

I calculated the stamp duty for a $40,000 GTR it is $1,540 plus the transfer and registration fees so I wouldn't go there with under $2,000.

As for insurance I use just cars. They are one of the few people that will insure an import without requiring a lock up garage, just MAKE SURE YOU GET AN IMMOBILISER AND ALARM!!!!

I haven't claimed though just cars so I can't say what that is like.

Hope this was of some help

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's excellent but I'm still breaking it in so I'm not 100% sure where it'll end up. I would say it's about 15% heavier than stock and the smoothness of the slip zone is quite progressive but you need to be a little patient compared to stock or it'll bite hard and stall. Stock I got away with absolutely horrid clutch control. Like I said before I couldn't even tell where the clutch would grab when it was stock so releasing way too quickly without enough revs it would just slip and the revs would drop lower than ideal but that would be the end of it. Currently there's a bit of a nasty clutch judder if I don't apply enough revs + find the exact wrong point of the slip point in the clutch pedal but it feels like it's slowly resolving as I drive it more. I would not recommend the competition clutch unless you really need the extra clamp force. I think this clutch combined with the Nismo operating cylinder is going to be exactly what I want. Enough bite that you need to remember the release point to avoid stalling or rough shifts, but progressive enough that it's not hard to drive by any means and not heavy at all. I tried a "super single" clutch on my friend's 997.2 Turbo 6MT and that was absolutely horrid. It runs an electrohydraulic power steering pump for the clutch power boost so there's zero feedback in the clutch pedal and there was a horrific clutch shudder well after break-in due to the lack of marcel springs or hub springs in the friction disk. It felt like the slip zone was the thickness of a single toe twitch as well so it was almost impossible to avoid stalling it unless you gave it a ton of revs and just dumped the clutch instead of trying to be smooth with it. I was terrified of pulling out in front of traffic. I have also tried some kind of "super single" on an EK9 and that makes this twin plate Coppermix look like a stock clutch. Releasing the clutch pedal even slightly too quickly feels like you're getting rear-ended. The pedal is extremely heavy as well and there's no vacuum assist like the GTR.
    • Yeah, well I was probably way underguessing the $300 figure anyway. Just multiplied a "normal" by 4 for the purposes of pointing out it's not cheap, particularly if it has to be repeated.
    • We have an alignment shop out here that does what you're talking about but he wants like 800 AUD a pop. DIY is "cheaper" but once you start accounting for the value of your time I'm not sure it's worth it.
    • The main catch phrase for any car is "the eye of the beholder", and "personal tastes and preferences" And as for the plastic "flares", I honestly think they look cheap and tacky, and I cannot see them aging well, maybe if they were body colour they might look better to my eyes, but, I would still prefer it the were more like the older WRX STI models that had the wider body metal panels In saying all this 5hit, I wouldn't buy a new WRX again, even if it had the wide body metal panels    
×
×
  • Create New...