Jump to content
SAU Community

Recommended Posts

HAHAHAHHAHA, Now I know you have nfi about tuning, Methanol cars need to be fkn rich to make power.

running lean or even Gasoline AFR's on methanol will make less power than Unleaded, might not ping, but wont make any power.

lets just get back on track

-but if u ask me we re doing it and ur reading it......................

and cars still runing fine!

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

  • 1 month later...

been making 430rwhp out of a stock internaled rb25 for over 2 years now.

car is thrashed regularly, and sees drift days, circuit days, hill runs and has done 1 boring ass drag day.

car ran @ 12.9 @ 119mph with full drift setup as drag racing just not worth altering the car for

figure has been made on multiple dyno's including hub and roller.

car makes full boost by 3400...

what turbo are you using?

  • 9 months later...

mid 400 s

here s the link to it at 440s

this is a 26 the 25 was sold

here s it at 485 rosting

571 with alittle traction problem

im pretty sure its in the 600s the piping pop off on this run

i think the power is good for now

we will test it and update

camero hooks, we lost about 6 cars (second and third gear doesn t have too much traction)

update before we sold the 25 it was almost 500whp

So we proof it to be reliable in the high 400s

It did 11.1@124

So you had it for 9 months???

5+years would be reliable in my book

9 months and a few runs down the strip doesn't mean much

update before we sold the 25 it was almost 500whp

So we proof it to be reliable in the high 400s

It did 11.1@124

With 480rwhp I ran 132.5mph... Your set up isn't special, it's not even that great and your dyno reads high :whistling:

With 480rwhp I ran 132.5mph... Your set up isn't special, it's not even that great and your dyno reads high :whistling:

Didn't you pull a low eleven? Ima head down the strip when I get my clutch sorted and get me some proof. I am hoping to get kicked out too.

And I am agreeing

And bringing more informationz!

And Ye... :mellow:

I must have taken the I'm with stupid the wrong way... Carry on :)

I think it was a very high 10 which is why he got kicked out.

It's in my signature guys... I mean come on :whistling:

With 480rwhp I ran 132.5mph... Your set up isn't special, it's not even that great and your dyno reads high :whistling:

simonR32

i just saw your built up thread (good job...)

thats what we were looking for someone that did it !!!

so your motor is stock right? and what was the highest power you made? also converted to whp

thanks

we ill see how the stock rb26 does at high 500whp than i post... to compare

Edited by Revspeed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Does it make a difference in your turbo having a shorter life if you have a cat converter as it causes that back pressure versus less/no back pressure with a decat? (Not sure if this is accurate) Also slightly different question if you went from a oem cat to a decat or vice versa will it require a tune? I heard if you change the dump pipe onwards it requires a tune?
    • No. Have only gotten as far as contemplating the task of having to put in the required fairly heavy wiring and fusing to run it (along with the big alternator), and preferring not to. But otherwise, it would be nice to have a little extra freedom as to exactly where the compressor is located and free up some space around the exhaust side of the engine.
    • Following from this in a related by not closely-related sense... Because I was buying a bunch of other GKTech stuff, I got some rear subframe collars. The history that leads up to this is: 25+ years ago the car arrived into the country with stock subframe bushes. At some point shortly thereafter I added Whiteline pineapple rings, set up neutral, and it improved the rear end behaviour. Well, it is my vague memory that I was happier with it with them in. Less axle tramp on launches, generally better, etc etc. ~2012 it got a new non-HICAS subframe with new stock bushes. No pineapple rings. I reckon that ever since then I've been dissatisfied with the axle tramp. Recently I've been f**king around a lot with all aspects of the suspension. One contemplation has been to relocate the rear lower control arm front mount points (and do the other things needed to make that work) to improve longitudinal rear grip by getting rid of some of the stupid anti-squat that Nissan ladled into the R32. But.... before doing that I thought I'd put some collars in. And.... The collars are good. The rear sounds a little bit different, but there has been no significant increase in NVH coming up into the body. In terms of rear behaviour - expansion joints on long sweeping elevated freeway ramps that would sometimes cause the rear to jiggle around a bit, no longer seem to do so. It appears that jamming chunks of metal into the gaps in the rubber so they can't move much is a really good thing. And the launch behaviour and general forward traction situation seems to be greatly improved too. It's impossible to be really sure, because the tyres are completely shagged - they are freakishly willing to let go right now. But as an A-B test with the same tyres it certainly seems to grip up a lot better. Highly recommended to anyone who still has stock bushes.
    • Bit off topic maybe but has anyone had a crack at one of those aftermarket electric compressors ? Bit of a search came up with one put out by Speedy Air Spares. Looks interesting and looks as if you'd have to run a big arse alternator. Found this out after the fact as my air con compressor packed it in and soon after my alternator ! !
    • Yes. Needs new ports. Usually just achieved by screwing an adapter onto them. Be aware that any AC compressor that hasn't been used in a long time will very likely have dried out seals and will not hold gas. Oh, and obviously you will require a new receiver-dryer also.
×
×
  • Create New...