Jump to content
SAU Community

Recommended Posts

So what should i do in wet conditions?

Slow down a little :(

Also at the track in the wet it often has more grip OFF of the racing line. (especially under brakes - brake more towards the in-side line if that makes sense).

The biggest mistake i see BY FAR for people new to the track is.. they just go for it straight up, with no warm up. I must have organised countless track days myself, and you can bet your bottom dollar after the first session, a good ratio of the newbies have cooked their brakes, blown diffs etc. Too much enthuse!

if it's wet at basky put your tyres up to about 50psi , if it's dry start with 38 in the front and 34 in the rear. Auto would be difficult around there , be prepared fro the skyline (the corner at the top of the hill) you can't see it 'till your on it , enjoy :( oh p.s expect to scrub your tyres heaps and your r31? does it have std brakes? they will die quickly as soon as you start driving it hard . kamikaze croall will be able to help you out heaps ;)

sorry fulla's only got her back yesterday and haven't been to the track yet, brakes seem stiffer then i remember so thats something i gotta tackle first. for those of you who haven't seen it yet, find my thread "STS Turbo Setup" in forced induction. Oh wait, here's the link, forgot i could do that: http://www.skylinesaustralia.com/forums/topic/340173-sts-turbo-setup/

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Cut sump up and extend. Win win 😂 
    • All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • also, we need to know which solution worked....
×
×
  • Create New...