Jump to content
SAU Community

Recommended Posts

Anyone have any ideas why my car misfires at two times:

1) cruising from 70-100 or so, then throw it back to 3rd, and floor it, i get a pause, about 3 small pops, and it takes off like a rocket. This is not so bad, just a bit annoying.

2) Taking a slow corner, or almost stop at lights or something, 2nd gear, low revs, if i give it too much too soon, i get almost full boost, but the revs wont pick up, it feels as if its choking, sometimes it misfires. I have to back off, let the pressure blow of, pick up the revs a bit, then floor it.

I have a SAFC, i dont think its fuel. The car has done this for as long as ive had it, im just getting sick of it.

Someone suggested spark, and pulling the plugs out, cleaning and gapping to 0.8 has made it a bit better. I have NGK plugs, any suggestions, new plugs (what brand), or other causes?

Link to comment
https://www.sau.com.au/forums/topic/3470-misfiring/
Share on other sites

It sounds like not enuf spark is getting through for one reason or another. Could be coil packs playing up, heres a cleaning technique I read in HPI (or was it Zoom?):

- clean the rubber boot on the coil pack with degreaser. Dirt and grime makes it easier for spark to find ground through the insulating boot rather than the spark plug

- spray the rubber boot with a silicon based spray to further insalate it. (I used WD40)

If none of the coil packs are terminaly fautly, hopefully that should sort it out.

NGK plugs are safest to use with our cars, they come factory standard on all jap cars I've seen. Whats the service interval for NGK coppers, 10-20k km? Probably best to replace them if you don't know when they were last changed.

Link to comment
https://www.sau.com.au/forums/topic/3470-misfiring/#findComment-58078
Share on other sites

yep, they are about 6000 k's old. There was some oil around the coil packs, which looked like it was clean, and put there intentionally, ill try WD40 or something. The coil packs actually look quite new.

I am going to get those expensive plugs, to see if it makes a difference, seings its only under high load, that it misses.

Link to comment
https://www.sau.com.au/forums/topic/3470-misfiring/#findComment-58152
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
    • From there, it was just a quick electrical check, prime the oil and start her up Which, is not what happened. 1. Bloody seppo Aeropro battery holder. Not only was it too tall for the battery (which I'll forgive them for, I have another battery the same nominal size that is taller than Neil's one, but the bracket is a fixed height so the battery was spaced up) But the thing that really shits me is the hardware to hold it on requires a 7/32 Hex key. WTF. No-one will ever be able to remove or install the damn thing without a hex key they don't own 2. Kill switch no longer worked once the console was installed. Neil mentioned above he had to adjust the length but it no longer cleared the console once installed. Sorted. 3. Suspiciously, the brake light holders were hanging in the boot with no globes. Sure enough the stopper on the brake pedal was missing so they are always on unless the kill switch is activated. Will pick one up tomorrow (turns out 32 and 33 don't use the same stopper) 4. All that sorted, I turned on the kill switch, turned the key to ACC. Nothing. Turned it to IGN. Nothing. Checked some fuses and found the main IGN in the boot was missing which improved things once it was replaced. Now ECU and dash lights turn on with IGN but still no fuel pump. 5. Turned it to Start....ECU on, no fuel pump, no starter. Plus the voltage dropped straight to 9v.  I suspect the starter is f**ked but am going to have to work through it all and see what is happening, really looks like more than one issue. Does anyone have the R33 fuse box key with the circuit it sources from (eg BAT, ACC, IGN, SRT etc) and supplies? I can find a translated list showing Amps and circuit without supply circuit, and I can find supply circuit without Amps and target circuit.
    • 3rd time lucky, the AAC is now all plumbed up after getting some final fittings All set up under the plenum of maximum access
    • OK, so the weight has been bugging because it was really low. I did it again today and got a more believable answer at 1246 without driver And with a 93kg driver I'm pretty sure the car was still slightly on the quickjack last time meaning the full weight was not on the scales  
×
×
  • Create New...