Jump to content
SAU Community

Recommended Posts

Anyone have any ideas why my car misfires at two times:

1) cruising from 70-100 or so, then throw it back to 3rd, and floor it, i get a pause, about 3 small pops, and it takes off like a rocket. This is not so bad, just a bit annoying.

2) Taking a slow corner, or almost stop at lights or something, 2nd gear, low revs, if i give it too much too soon, i get almost full boost, but the revs wont pick up, it feels as if its choking, sometimes it misfires. I have to back off, let the pressure blow of, pick up the revs a bit, then floor it.

I have a SAFC, i dont think its fuel. The car has done this for as long as ive had it, im just getting sick of it.

Someone suggested spark, and pulling the plugs out, cleaning and gapping to 0.8 has made it a bit better. I have NGK plugs, any suggestions, new plugs (what brand), or other causes?

Link to comment
https://www.sau.com.au/forums/topic/3470-misfiring/
Share on other sites

It sounds like not enuf spark is getting through for one reason or another. Could be coil packs playing up, heres a cleaning technique I read in HPI (or was it Zoom?):

- clean the rubber boot on the coil pack with degreaser. Dirt and grime makes it easier for spark to find ground through the insulating boot rather than the spark plug

- spray the rubber boot with a silicon based spray to further insalate it. (I used WD40)

If none of the coil packs are terminaly fautly, hopefully that should sort it out.

NGK plugs are safest to use with our cars, they come factory standard on all jap cars I've seen. Whats the service interval for NGK coppers, 10-20k km? Probably best to replace them if you don't know when they were last changed.

Link to comment
https://www.sau.com.au/forums/topic/3470-misfiring/#findComment-58078
Share on other sites

yep, they are about 6000 k's old. There was some oil around the coil packs, which looked like it was clean, and put there intentionally, ill try WD40 or something. The coil packs actually look quite new.

I am going to get those expensive plugs, to see if it makes a difference, seings its only under high load, that it misses.

Link to comment
https://www.sau.com.au/forums/topic/3470-misfiring/#findComment-58152
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is there a shroud around the tailshaft spline into the back of the box? They can rub and make a horrible noise if they are not on straight/damaged. The heat might have caused it to grow too much in one direction and rub.
    • Strangely I noticed it either disappear later in the day, or not be present. I definitely noticed when I was crawling around that open wheel thingy entering the pits (that part was audible in car). Driving home and commuting around town for example, I didn't hear it. It's plausible that it was a brake disc or something still slightly in contact. The brakes absolutely felt BAD for the first couple of sessions, huge amounts of shudder and grinding as they got up to temp - And then I actually just forgot about it as the day went on/didn't notice it. The videos were from the morning when this was more present than the afternoon/drive home when it wasn't. I've asked around and got a variety of responses including handbrake shoe contacting hub, CV joints, CB tailshaft bearing as above, and clutch input bearing. I didn't test if it disappeared when clutch was in. I haven't noticed it in any of the other videos nor did I notice it when driving to that extent. More or less hoping the microphone at the rear license plate giving some kind of clue of 'something' but it looks like "spin stuff and see if you can notice it" is the way forward here. I could be smart and use the gopro mic and re-mount it to that location to see if the sound is still present at low speed actually. Sounds like a decent test whenver I have the CBF'ness to drive the car again. Given it's almost 40C for the day of the track day and the next 3 days after, the CBF is high. All I've done since getting home is unpack the car, remove the remnants of the lip and undertray and left it there. I was surprised how well the PMU Club Racers actually worked. The brake performance on the track was absolutely fantastic, best I've ever personally used, no fade whatsoever and the bitiness was almost too good, I was scrubbing more speed off than I needed to, but I also ended up infield when I started trying to scrape off ... less speed.... so...
    • Not really, no. Anything you would do is easily reversible.
    • I would like more noise related info for my truly uneducated guess  Does it do it at idle or when revving, clutch engaged, and disengaged? Does it only do it when the car is moving? I've heard "similar" noises from a clutch pack that left the chat room, and CV joints that have chewed themselves out But as Matt said, how's the yokes, tailshaft and centre bearing going after their last little issue Fingers crossed it is something simple  Weird noises make me cringe 
    • One other question, is there a chance that changing the idle speed can lead you down a rabbit hole and is the reason the tuner didn't touch it? Reason I ask is because if that's the reason the tuner avoided it then I probably shouldn't be touching it lol.
×
×
  • Create New...