Jump to content
SAU Community

R33 Gtr Front Cut Part Out!

bigmikespec
 Share

Recommended Posts

bigmikespec Veteran

bigmikespec

Posted
Posted (edited)

Have a bare front cut that I bought; came with a few parts that I do not need:

Heater core: $50ea (I have two available)

Bonnet hinges: $25 (pair)

Clutch pedal: $50 (with brackets)

Brake pedal: $50 (as above)

Accel. pedal: $50 (as above)

Indicator stalks: $25ea

A/C compressor with lines: $100

Standard clutch with flywheel: $150

Steering column with ignition barrel: $150

Airbag: $200

Fuse box with wiring loom: $150 (engine bay)

BOV recirc. cross over pipe: $100

Wiper motor with mechanism: $100 (front)

Hard pipe ABS lines: $50

Washer bottle bracker: $15

Washer pumps: $10ea

Scissor jack: $25

I have done a bit of research as far as prices are concerned. I can post at buyers expense and located in Adelaide, SA. I will try and get some photos when I can.

Please PM or SMS me: 0432 562 025

Cheers,

Mike

Edited by bigmikespec
Link to comment
https://www.sau.com.au/forums/topic/347276-r33-gtr-front-cut-part-out/
Share on other sites
bigmikespec Veteran

bigmikespec

Posted
  • Author
Posted

Washer bottle bracket sold pending payment, thanks Johno.

Remaining items:

Heater core: $50ea (I have two available)

Bonnet hinges: $25 (pair)

Clutch pedal: $50 (with brackets)

Brake pedal: $50 (as above)

Accel. pedal: $50 (as above)

Indicator stalks: $25ea

A/C compressor with lines: $100

Standard clutch with flywheel: $150

Steering column with ignition barrel: $150

Airbag: $200

Fuse box with wiring loom: $150 (engine bay)

BOV recirc. cross over pipe: $100

Wiper motor with mechanism: $100 (front)

Hard pipe ABS lines: $50

Washer bottle bracker: $15

Washer pumps: $10ea

Scissor jack: $25

bigmikespec Veteran

bigmikespec

Posted
  • Author
Posted

Heater core: $50ea (I have two available)

Bonnet hinges: $25 (pair)

Clutch pedal: $50 (with brackets)

Brake pedal: $50 (as above)

Accel. pedal: $50 (as above)

Indicator stalks: $25ea

A/C compressor with lines: $100

Standard clutch with flywheel: $150

Steering column with ignition barrel: $150

Airbag: $200

Fuse box with wiring loom: $150 (engine bay)

BOV recirc. cross over pipe: $100

Wiper motor with mechanism: $100 (front)

Hard pipe ABS lines: $50

Washer bottle bracker: $15

Washer pumps: $10ea

Scissor jack: $25

Front upper control arms: $50 (pair)

Rear lower control arms with ball joints: $100 (pair)

Rear upper arms: $50 (all four arms)

Front swaybar: $30

Rear lower control arm with ball joint: $50 (LHS only)

Rear upper control arms: $25 (LHS only, both arms)

Rear swaybar for R33 GTS: $20

Electric HICAS unit: $25

Bridgestone RE050 245/45/17: $100 (pair, good tread left!)

Please take this stuff away!

Johno bracket was sent today sorry for the delay.

Mike

  • 2 weeks later...
  • 3 weeks later...
  • 1 month later...
bigmikespec Veteran

bigmikespec

Posted
  • Author
Posted

Bonnet hinges sold thanks Troy... plenty more parts left:

Heater core: $50ea (I have two available)

Clutch pedal: $50 (with brackets)

Brake pedal: $50 (as above)

Accel. pedal: $50 (as above)

Indicator stalks: $25ea

A/C compressor with lines: $100

Standard clutch with flywheel: $150

Steering column with ignition barrel: $150

Airbag: $200

Fuse box with wiring loom: $150 (engine bay)

BOV recirc. cross over pipe: $100

Wiper motor with mechanism: $100 (front)

Hard pipe ABS lines: $50

Washer bottle bracker: $15

Washer pumps: $10ea

Scissor jack: $25

Front upper control arms: $50 (pair)

Rear lower control arms with ball joints: $100 (pair)

Rear upper arms: $50 (all four arms)

Front swaybar: $30

Rear lower control arm with ball joint: $50 (LHS only)

Rear upper control arms: $25 (LHS only, both arms)

Rear swaybar for R33 GTS: $20

Electric HICAS unit: $25

Bridgestone RE050 245/45/17: $100 (pair, good tread left!)

  • 3 weeks later...
  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Ticking Sound On Idle - Rb25

      By GTSBoy 路 Posted

      Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • myrbgivesmeheadaches
      Ticking Sound On Idle - Rb25

      By myrbgivesmeheadaches 路 Posted

      Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • GTSBoy
      Ticking Sound On Idle - Rb25

      By GTSBoy 路 Posted

      This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • myrbgivesmeheadaches
      Ticking Sound On Idle - Rb25

      By myrbgivesmeheadaches 路 Posted

      Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • MBS206
      NC MX5

      By MBS206 路 Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
脳
脳
  • Create New...