Jump to content
SAU Community

Recommended Posts

For sale is my much beloved drift car:

Nissan Skyline, R33 Series II, 1996

Interior still A1 seats all good no interior been stripped,

Front bar not on photos but will go in sale

Ok lots and lots of mods forgive me if i forget some below"

-Aftermarfket forward facing plenum custom

-Z32 Air flow meter

-HKS gate with screamer

-Slotted front roters with new rear bendix brakes

-Flared and rolled rear guards

-Big FMIC custom stainless piping

-HKS coil overs

-3" exhaust system

- Access tuned Apexi power FC with hand controller

- Momo aftermarket racing wheel

-Apexi power intake air pod

-Cusco and HKS sway bars front and rear

-Aftermarket oil catch can

-Built RB25 motor done hardly any k's

-Bosch 040 fuel pump

-Greddy dual stage boost controller

-HKS turbo timer and secondary boost guage

-Garrett aftermarket huge will update type later

-HKS bov

-Bayside clue with fibre glass kit

-Heavy duty clutch

- New 25 Gearbox

-660 Nismo injectors and fuel rail

Contact me on 0431-388-718 or pm me

Car is in Adelaide can be sent to all states

post-51163-0-51145900-1292385049_thumb.jpg

post-51163-0-33831100-1292385217_thumb.jpg

post-51163-0-02564200-1292385306_thumb.jpg

post-51163-0-67414600-1292385422_thumb.jpg

Edited by sus34
Link to comment
https://www.sau.com.au/forums/topic/347606-r33-series-ii-drift-car-fs/
Share on other sites

mate does it need much to get rwc? Does it have a locked/welded diff that made it defected or something else?

No welded diff mate, car had rego up till febuary. It's only been tracked twice. Which state are you I'n..?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...