Jump to content
SAU Community

Recommended Posts

I can't remember, and i am not searching but don't R34 gtr turbos have smaller exhaust housings? .64 vs .48?

theres enough info on the net with back to back BB versus journal and i've backed to backed it aswell,(BB T28 versus journal) transient response is "slighlty" better, but only really noticed on light throttle openings(1/4 throttle, bringing up a few pounds of boost ), so maybe for a motorkhana car its worth it, for the rest of us it won't make a difference

cheers

darren

they both use the .48 rear housing.

even without seeing jez's results yet, i rekon the td06sl2-20g is already a winner for a rb25 without too much lag.

if i can manage to low mount this and weld the gate straight onto the rear housing (38mm will def fit, not sure about 44mm??) then it will be something i will do.

will wait for ARTZ to see how he goes with low mounting his unit.

I'd be going the 40mm comp gate anyway 1. because it should sound better 2. because its cheaper!

trent seems to use them often with no issues.

yeah i want to cause its a very compact unit..

..but tial comes with 7 different springs TS comes with 7psi only which means I need to buy more springs :(

ill see how much i can score some for.. :)

pipe i have is 46 Outside 40 Inside.. so i measured it up..and although it looks like ti will fit from the outside but when I measured the inside of the turbo housing, because of the thickness of the walls, I think a 40mm hole is going to be the limit as the inside of the housing just wont accomodate a 44mm hole. so even if i have a 44mm gate im only going to have a 40mm pipe feeding it.

DSC03098.jpg

from everything i have read, it is meant to be the best place for it, run it off at an angle less than 90 degree and it should have great boost control..

TS site says to keep the gate at least 100mm away from the housing though, away from the heat as much as possible Guess i will take my chances with it under a heatshield....

wg.png

**Although this setup may work on paper i really have doubts as to its sustainability if it was running hot for extended periods..**

Simon,

what BOV are you running? (If any that is)

cheers

Greddy Type R

Damn beat me to it!

http://www.skylinesaustralia.com/forums/index.php?showtopic=345095&view=findpost&p=5748802

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It's impossible to convey what it will feel like to get the right torque. But you can develop a feel for it. A 900mm breaker bar is.....f**king huge. I only use a normal ~400mm one. But with 900mm being very nearly a metre, and the right torque being in the order of 100Nm, then you're going to need a bit over 100N of force, which is about 10 kg. So if you practice using the bar pulling up, instead of pushing down, then it will be about the same effort as lifting a 10kg bucket of water. That's what the pressure against your fingers should feel like. Ish. If you use a more typical length breaker, then it's about twice that. So a good 20 litre bucket, or a little bit more.
    • Also, if anyone has a torque wrench around Williams Landing area and can lend it to me for like 5 mins - I got 4 bottles of Furphy left and I’ll throw that in with a Happy meal 😂
    • So today I decided to bleed my brake fluid, which meant to the wheels came off the car at my garage for the first time. I only had a 90cm breaker bar with me and I noticed that some 1 or 2 lug nuts were a bit hard to get loose (from when the shop did the coilovers) Now.... when it came to putting them back on, I didn't want to put all my weight and overtighten them. So I hand tightened as much as possible and then put normal pressure on the edge of the breaker bar and tightened it until I couldn't turn it anymore without putting in an effort. Do you think that is tight enough? Or is that still too tight?  They are tighter than finger tight. Last thing I want is to have them strip or warp sh*t. But hard times mean I can't just go down to Supercheap and get a torque wrench 🥺
    • Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
    • I don't think that's what you're seeing. Something else doing that. The only time I've seen it get so retarded is when it's trying to control idle (in which case we're not talking about mapped timing tagets anyway) and when there is an extreme coolant temperature sensor fault. The RB26 ECU is essentially the same as the 20 ECU and I knew that ging inside out. There is no facility for it to retard that heavily on cold start. The OEMs never used to do it back then. I mean, shit, the catalyst is abotu 3 miles down the exhaust anyway. Early light-off was just a twinkle in some EPA arsehole's eye back then, not a regular engine control strategy.
×
×
  • Create New...