Jump to content
SAU Community

Recommended Posts

Here you go Jez

2hq8qp4.jpg

As far as I know, it's a untouched RB25. Full boost is actually 5750rpm lol, as you can see it's a slug to drive off boost too.

I've spoken to Eiji and they do make a 10cm rear for my turbo so I'll probably get that sometime next year.

Really wasn't expecting it to be THIS laggy, live and learn I suppose.

wow laggy and no power at all! im selling a td06 that will make best part of 300wkw and be way more fun than that if you keen to move on

Honestly. pull it off and count the blades, measure the wheel diameters. Along with what others have said its possible that the wheels are not what you ordered and its some other beast all together. With sooooo many turbos its not a stretch to see the wrong spec turbo being delivered.

Here you go Jez

2hq8qp4.jpg

As far as I know, it's a untouched RB25. Full boost is actually 5750rpm lol, as you can see it's a slug to drive off boost too.

I've spoken to Eiji and they do make a 10cm rear for my turbo so I'll probably get that sometime next year.

Really wasn't expecting it to be THIS laggy, live and learn I suppose.

for that setup the 12cm is no good.

count the blades, measure the wheel diameters... its possible that the wheels are not what you ordered .

Owners comments were that it's a TD06-20G, with 12cm housing.

By my reckoning that's broadly equivalent to a GT3571, and a 1.00A/R turbine housing. Looks much more like something you'd see on a reasonable sized diesel eg. Landcruiser 1HZ.

Of course it will be slow to respond. Simply wrong spec for the engine and application.

It's a TD06S and it is a T3.

Spewing eh! Ahwell I got it cheap ($600 via Ebay special). Atleast it's fixable, just a pain in the arse lol.

I wonder if Raz' 10cm rear would fit my turbo, hmmmm.

Cheers for all the help guys :)

back on topic tho id say put some more boost into and get it back on the dyno but def 12cm rear is no good

  • 2 weeks later...

hey guys

sorry too start again but there is 240 pages and am in need of a new turbo and cant be bothered going through the hole thread.

i am looking at around 260-280rwkw on my r34 rb25 neo.

my supporting mods at the moment are

full 3" exhaust

fmic

hks low mount mani

hks 38mm external gate

pod filter

apexi pfc

greddy profec b spec 2 boost controller

walbro 255 fuel pump

370cc injectors

will most likely be getting a set of 660cc injectors shortly.

what would be the recommendation for that kind of power figure with minimul lag?

thanks guys.

Predicting strong torque between 5-8000rpm. Going by the pic associated with the post it's optimal use is on a drift spec engine.

That's pretty high up in the rev range, out of interested, would a 10cm housing start the torque down at maybe 3500rpm or so? something?

hey guys

sorry too start again but there is 240 pages and am in need of a new turbo and cant be bothered going through the hole thread.

i am looking at around 260-280rwkw on my r34 rb25 neo.

my supporting mods at the moment are

full 3" exhaust

fmic

hks low mount mani

hks 38mm external gate

pod filter

apexi pfc

greddy profec b spec 2 boost controller

walbro 255 fuel pump

370cc injectors

will most likely be getting a set of 660cc injectors shortly.

what would be the recommendation for that kind of power figure with minimul lag?

thanks guys.

Get a T67-25g it'll make that power easily. Just so happens I have one for sale. ;)

That's pretty high up in the rev range, out of interested, would a 10cm housing start the torque down at maybe 3500rpm or so?

With stock-spec engine internals (ie cams, CR) in a 25DET that seems to be commonly achieved with the 10cm housing. The 12cm and cams should result in pushing the torque curve to the right, probably a good thing for a drifter with clutch kicking.

Can't readily see why the 20G comp would be the thing of choice over a 25G for that performance target. Much the same situation with the Garrett range GT3076 vs GTX3071, the performance outcomes are lineball because the smaller comp has to spin faster to pump the air-mass.

That said, it's an option that should hit the nominated power range without too much problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, fun day was had, I finally found a house that will do me just fine, 1980's brick build, but with full fresh renovations, plus new colour bond fencing all round so puppies are incoming 馃悤, and water tanks for the garden, and it's located in West Goulburn..... @Duncan 馃, so day trips to Wakie to watch cars going Zoom will be on the cards In the end it cost well under my budget and was actually better than alot of the more expensive joints I was looking at, it is in a good area, close enough to the shops, public transport, and the Wollondilly River Weir,  and the great walking paths along the river, but far enough away from town to see minimal traffic The deposit is dropped, the conveyancer is conveyancing and I should get the keys in a week or 2 as the property is currently unoccupied  As with everything I own, I'm doing up a modifications list, as it doesn't have solar, that is first up on the big list, all of the panels and enough batteries to keep the joint warm, or cool, followed by a largish carport out the front, the small list, which will start as soon as I have keys, is some security stuff, like cameras, screens, and the usual "crazy prepper" additions that weird old people like (mouse holes to stick shot guns out of, and the usual man traps that the average person installs for the unsuspecting and unwanted guests 馃ぃ) The gardens front and back are OK, but, not to my standards or liking, so landscaping will be a fun job to start getting into, so when spring is sprung I'll do a heap of planting, lots of natives and vegetables is the plan, the old owners were more "Old English Garden" type, so basically Roses and other weird looking things that are destined for the green waste bin One thing that is staying garden wise is a nice established hedge out the front, it is about 5 foot tall and covers the whole front of the property from prying eyes As for the car hoist, the roof in the garage has some height to it, but, I'll need to get an installer out to see what can be done, width wise may be a issue, but my building inspector will be getting back to me over the next week with his recommendations  Small, but cosy     
    • I tried to get in contact before I went to QLD you didn鈥檛 respond, then I tried to contact you in r31 club.  I thought you fell off the earth or something haha.  I will grab it off you but unknown when I will be up that way 
    • I think that might be in the question. He is going very low, and I think the standard GTR ones are simple tripod joints (like the rear NA/S chassis ones), not proper CVs (like R chassis turbo/GTR ones). Proper CVs take the misalignment better than tripods.
    • Do you still need the wiper motor and stuff?
    • I haven't used the Crank Motorsport ones, but can I ask why not use standard gtr/gts4 axles at the front? They would easily cope with that power level. BTW.....sounds like quite the project!
  • Create New...