Jump to content
SAU Community

Atr43 G3

Kenna802

By Kenna802,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

Kenna802 Experienced

Kenna802

Posted
Posted

HI all,

If anyone is interested ill post my pics for the install of an atr43g3 turbo from a factory standard install. First things first remove the old turbo. easy as except removing the water lines ( it does take a bit of force) and also move your power steering out the way.

Link to comment
Share on other sites
Kenna802 Experienced

Kenna802

Posted
  • Author
Posted

I already had the turbo out before i took the pic's sorry :)

All i did was unbolt the airbox piping and airbox and cooling pipes going to the turbo and plenum and than unbolt the 6 bolt flange. This all in all didn't take too long.

After that remove the oil lines and water lines on the turbo ( u will need a bit of force for the water lines) also slide the powersteering bottle off the bracket and just move it away for the time being.

I had to get some longer exhaust flange nuts because of the spacer. ( you will need an extra gasket for this as well ) I also did a trial fit and had to knock out the tower slightly in order for it to fit.

No heres the tricky part i want to retain most of my existing set up so i am getting bits made up to look stock as possible. I can use half of the original intake pipe but i will have a 3 inch ali piping going up into it so it will not suck shut. You will need a 4inch to 3 inch silicon converter, and some 3 inch piping ( which will be getting ali welded to fit the plumb back pipe and hose going to the catch can. This is currently getting being made and will post more once parts have arrived.

Link to comment
Share on other sites
Aleckr33 Rising Star

Aleckr33

Posted
Posted

nice man, i bought a atr43g3... im thinking of DIY as well to save some $$$..anyone know if i can i do this and get a tune after installation of turbo? like is it safe to drive the car normal just till i get a tune?

Link to comment
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

it's safe to drive the car with that turbo provided you run low boost and don't floor it too much. tune wise on the stock ecu it will be safe but it would just be getting close to hitting the airflow protection, which would just making it annoying to drive. if you already have an aftermarket ecu with a tune on it then the same would apply (low boost and don't give it the beans much) but you lose the added safety of built in overboost protection.

but to simply bolt the turbo on and drive to the tuner would be fine as long as you take it easy.

Link to comment
Share on other sites
Kenna802 Experienced

Kenna802

Posted
  • Author
Posted

Nice i have an emanage ult installed in the car running a z32 afm i have also just upgraded the injectors but i have not included any pics as im trying to forget the experience :)

I will be bringing the car over to gympie to get it tuned rain is slowing my progess but dump pipe is now bolted on

Link to comment
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

you taking it to gary to get tuned?

ahahaha, yeah injectors are a pain to change, especially if you don't remove the plenum (found that one out the hard way).

yeah the rain is a bit of a pain at the moment. if this rain that is predicted over the next few days actually does happen then you may find you aren't able to get here, as well as gary's workshop having a few feet of the river in it, LOL. very high chance of it flooding if we get a few days of decent rain.

Link to comment
Share on other sites
Kenna802 Experienced

Kenna802

Posted
  • Author
Posted

OK update,

water feeds are now on as well as oil feeds. I spent about 9 hours trying to get standard water feeds to line up with NO success . I had to cut them and put piping in in order for them to bolt on.

Just found another set back turns out the 4-3 inch pipe has not been sent even though i payed for it on saturday. Turns out the supplier had not recieved the email from paypal. Looks like this puppy wont be ready for xmas excuse me while i scream....

Link to comment
Share on other sites
Kenna802 Experienced

Kenna802

Posted
  • Author
Posted

All in all i wouldnt recommend doing it urself unless u had some one to help because i did most of the work by myself and things can get very difficult. overall if u have some mech experience ( unlike me ) u will be fine it just took me about 10 times as long :)

Link to comment
Share on other sites
  • 1 month later...
  • 3 weeks later...
  • 1 year later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • GTSBoy
      Compatible rear drive shafts R34 N/A?

      By GTSBoy · Posted

      They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
×
×
  • Create New...