Jump to content
SAU Community

Recommended Posts

Hey guys i just got a power fc for my rb20 which is r32 spec but in a r31.

I plugged it in etc

Have power to the ecu when i turn key it primes (for shorter then old ecu) and it will crank but it wont turn over. The tune in the ecu is for a similar spec car but is tuned for 550 injectors not the standard ones that i have. i dont want to drive the car or anything i just want it to turn over and see how it works.

Any ideas, i dont really want to reset the tune because its probably useful.

Cheers

Sean

Link to comment
https://www.sau.com.au/forums/topic/34839-power-fc-trouble-shooting/
Share on other sites

Just go to the setting menu, then injector and change the the Injector Data from 100% to (old injectors cc/min)/(new injectors cc/min)*100. This will get you in the "ballpark" of where you want to be.

You can also go into the Ign/Inj menu and screw around with the Ing settings till you find a setting that runs nicely (keeping an eye on AF of course) and you should be fine. Then once you work that out, apply the fudge factor that worked well to the Injector Data and Bob's your father's brother...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Meh, At 60 years old, I have been doing dumb stuff for much longer than you mate, I am the true King And unfortunately I cannot be a maroon, as I am not brownish red As for not getting ITB's, the plenum intake will apparently show typical gains across the board and increase induction noise a bit, but, have all over less dort than ITB's Cost difference for the extra ITB dorts was significant though, the total parts for the plenum set up is "around" $2kAUD plus shipping, the ITB's were $4kAUD plus shipping, I was contemplating really hard about paying the extra $2k for all of the dorts, but weirdly, some form of common sense, from listening to the platform experts prevailed  As for the NA mod hate by some, I've had a few boosted cars, with all their inherent issues, I'm now looking at simplicity and legalities for a street car, maybe I'm just getting old, and I'm quite happy to spend some of the kids inheritance, 5kw at a time 🤣 And think of all the money I'll be saving on consumables that something with boost needs, like engines, gearboxes, diffs, clutches,  tilt trays... etc. etc. etc. 🤪
    • Haha.  I wouldn't say I am either but I've definitely been around it plenty.  I'm guessing you know the dial in is basically to make a handicap to level the playing field between racers.  The car with the slower dial in goes first and in theory if they run their dial in time and the faster car also does then they cross the finish time if they also have exactly the same reaction time - if you go faster than the dial in them you lose, but if you are too slow there's a good chance the other person will get to the finish line first. I'm normally supporting other cars but they were all pretty dialled and were egging me on to race as well, here's one of the cars I tune (Starlet) which ran within like 1 hundredth of its dial in through the competition: https://www.youtube.com/watch?v=inEBu-d9Gn4&t=69s
    • Where ever the fuel reg gets it reference is what I use to T into for map reference been a very long time so where it goes to plenum/runners I have no idea but never had issues. 
    • What ecu? Same shop every time? Same ambient temperature? If timing is correct then pull plugs and see if lean or rich. Dyno can also read different if they have changed ramp rate or not set tacho/speed properly  
    • I've never done dial in's just straight up, whatever that's called. I'm far from a drag (racing ) expert.
×
×
  • Create New...