Jump to content
SAU Community

Recommended Posts

Replaced the AFM this morning, and she roars into life!

I don't know what kind of Nissan engineer thought it needed security bolts... guess its so they can sell the whole tube.

Also the part number I received ended in 61A, not 611, for other people's info.

Replaced the AFM this morning, and she roars into life!

I don't know what kind of Nissan engineer thought it needed security bolts... guess its so they can sell the whole tube.

Also the part number I received ended in 61A, not 611, for other people's info.

61A? hmm did it have the temerature sensor in the unit? and 5 pins on the plug?

I'll be in this; it's high time I got back for a comparison to my bone stock 14.9 sec quarter over a year ago.

Got to be good for a 14.8 by now...whistling.gif

hoping for close to 14.0-14.1.... :)

61A? hmm did it have the temerature sensor in the unit? and 5 pins on the plug?

Looked the same bar a couple of markings. Diode on the outside. 5 pins. Works like a charm.

Only recently got my Stag. Traded it for my old 180 track/street car.

Came with some fugly looking rims so picked up these CR's and also got the NA grill to put on next and tinted the front windows to match the rear tint.

post-19472-0-24569700-1324727452_thumb.jpg

Fitted a new Pioneer 7300BT head unit yesterday, sounds good, will sound even better once I get my amp & speakers in. Getting the old tape deck out was certainly a challenge.

I seem to have a screw left over from somewhere, that's fast becoming my DIY signature whistling.gif

A bit sad for Christmas day, but the outlaws were over for lunch so, to ensure my day wasn't a total fail, I changed the oil.

A bit sad for Christmas day, but the outlaws were over for lunch so, to ensure my day wasn't a total fail, I changed the oil.

lol .... if only it wasn't raining I would be doing the same.

Had a look at doing the wire snip, because I've been slack and haven't it yet.

Are you guys just cutting back the covering on the ECU harness and cutting the pink wire with the blue line?

Its not as if you can cut pin 55 directly...

Im just going to cut it in the morning then wire up a switch later in the week.

Had a look at doing the wire snip, because I've been slack and haven't it yet.

Are you guys just cutting back the covering on the ECU harness and cutting the pink wire with the blue line?

Its not as if you can cut pin 55 directly...

Im just going to cut it in the morning then wire up a switch later in the week.

Tbh....I only really. Priced a difference when doing a stall and launch....but then again I have awesome and another.

Came with some fugly looking rims so picked up these CR's and also got the NA grill to put on next and tinted the front windows to match the rear tint.

i had some grey CR-Kais on my silver series 1 they look great. :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wanting to avoid this if possible but kinda looking like I may not have a choice 😭
    • Ok awesome thank you. Just wanted to have them in case I can find some and need to compare part numbers!
    • All I can say Duncan is good luck and I hope that Neil did not run any E85 in Cheryl. I have recently experienced the full spectrum of fuel tank issues in my R33's that had been caused by E85 and contaminated fuel. When you take the cover off the top of the tank and have a look inside you will get an understanding of how easy it will be. Best case situation is clean fuel with minimal contamination. My GTR was like this and it was a very simple operation to just grab the fuel pump carrier bracket and slide it up and out of the tank. My three GTS_T's had different levels of fuel contamination that was probably caused by E85 in the fuel.  In the worst case all of the metal components in the tank had rusted to the point where there were pieces of rusted metal swirling around in the tank. This required the removal of the exhaust, the tailshaft, the complete rear cradle and the fuel tank. The components in the tank were that rusted that it took days to get the fuel pump carrier and the mounting brackets out of the tank. When the tank was finally cleaned, everything inside the tank had to be replaced. With the tank all back together I could then reinstall it in the car along with everything else that had to come out. Good luck and I hope that you find a clean tank.    
    • It is a two door. It is black and also still has the OEM wheels and stereo. Exact model would be KR_R32RGFEL_SS According to GTR-Registry.com is a 2 Door Coupe; RB20DE; 2WD no HICAS; MT.F5; (11L) Projector Headlamps and Fog Lights; (12_) Electronic Active Full Auto Air Con (Climate Control); (13-14SS) V Selection -- Which seems to be accurate description of my variant. Will try to upload a few pictures soon. The OEM wheels look like the below image. Image is taken from the goo-net-exchange website.  
    • Time: Saturday 18th January - 9am -10:30am Where:  Cafe By Lamanna 10 English St, Essendon Fields VIC 3041  - https://g.co/kgs/mhVKvAB Registration: So we can give the cafe a heads up on rough booking numbers please rsvp below Registration Link: https://forms.gle/wPtfj9Gp8bvCiouo8
×
×
  • Create New...