Jump to content
SAU Community

Recommended Posts

My new track rims, lightweight Forged Rays (oem V35 rims I think, I haven't seen this style before) with Dunlop Direzza 036 soft compound semis. Should stick like glue. :)

post-63525-0-18565500-1349737383_thumb.jpg

post-63525-0-35562900-1349737394_thumb.jpg

^^ Sexy...

Finally finished wiring the EVC in last night, just have to finish the plumbing tonight (only have the MAP line in at the moment).

For Leon especially, and others, here are some pics of the direct 12V distribution block I setup.

post-34363-0-64824600-1349739575_thumb.jpg

That's the distribution block mounted next to the TCM. One 4GA wire in, and four wires out. Once problem I've noticed is the stock wires for the Wideband and EVC are too small to mount in here, so I have soldered in some thicker cable (the two black wires going in). You can also see the brown wire connected to the ignition power source of the TCM, which is used to switch the relay.

post-34363-0-15783900-1349739694_thumb.jpg

70A relay wired up in the battery compartment. You can see here the solid red wire, which goes to the battery, the translucent red wire, which runs to the distribution block, the translucent brown wire, which is the ground for the switching, and the brown wire running in, which is connected to the opposite side pin to the translucent brown wire.

post-34363-0-71441400-1349739811_thumb.jpg

Inline 50A glass fuse connected directly to the battery, and running to the relay in the above pic. The other red wire with the inline blade fuse is the direct feed for the fuel pump.

post-34363-0-99446700-1349739916_thumb.jpg

The end of the ground wire for the switching on the relay. Not very exciting but thought I'd throw it in anyway.

I'll post up some pics of the EVC install once it's done, hopefully I'll get the pics done tonight.

Boost controller finally in and working...

but...

In a stupid story in the vein of Dale's recent experiences, I started the car ready to go after setting up the EVC with a starting boost of 12PSI.

I put my foot down and revved the car, and next thing you know there's a bang, a puff of smoke, and a tink tink tink that scared the crap out of me.

I'm sitting here thinking "oh no, what have I done, engine go bang!" and turn it off straight away.

I rush round the front to find that one of the belts has shredded in half.

More "Oh shit", followed by a sigh of relief as I realise the smoke was a bit of belt hitting the clutch fan, and the tink noise was the left over bits of belt hitting bits of metal.

Pack it up, come inside, thinking "I can't be the only person who's had this happen, need to search the forums".

Do search.

Find three helpful threads.

One being Matt's new thread with all the part number he's found in it, including the AC and drive belts: http://www.skylinesa..._1#entry6541105

One being Justin's thread about his AC belt, with a very familiar image in it: http://www.skylinesa..._1#entry6392240

Enter sigh of relief as I read Alex's posts confirming that not only is the belt cheap and easy to replace, but I can clip it off and keep driving the car!

I love these forums...

I was initially worried it had something to do with the boost controller. Now that I know it's the AC belt it makes a bit of sense, as the AC hasn't worked since January and I figured it needed a regas.

So now I'm ordering a new drive and AC belt thanks to Matt's part numbers, cutting the AC belt thanks to Alex's help, and driving the car to AM Performance, which will be where it rests while I'm in Coffs, so Andrew can finally do the intake.

Some pics of the boost controller install will follow tomorrow, but thanks for all the help guys. Just wish that bloody actuator wasn't so difficult to get to!

Nice pick up there on the wheels Scotty. Special edition 350z wheels I believe - right out the Rays factory.

I bet they are worth a lot more than I paid. ;)

They were an option; only available on the 350Z track edition (with Brembo's), and were around $3800-$4000.

I think I've only seen 2 or 3 sets EVER; so they're pretty damn rare.

Scotty stole them cause of a hot tip off, Dale. ;)

Trading post says 1800. Seen for similar amounts in the past. Just like a proper rays wheel, without the cost.

Ryan. Alex takes no liability in what you cut off! :P

That's the awesomeness of search!

Why did you need to get to the actuator Ryan? Just to replace the hose? I would have left it and just plumbed it in where the T piece goes.

If you'd have told me that 6 hours ago thats what I would have done in hindsight!

But yeah, it was for the hose, and it worked out ok in the end, just a pain at the time.

Installed a nice yellow addition to my car,

Oh wait, that was the popo.

A dead number plate light and an apparent oil leak.. I can't see an oil leak anywhere...

So in actual fact, there's nothing really dangerously wrong with your car, but because it's different (and maybe the cop was in a shitty mood?), they decided you needed more hassles...

A dead number plate light and an apparent oil leak.. I can't see an oil leak anywhere...

So in actual fact, there's nothing really dangerously wrong with your car, but because it's different (and maybe the cop was in a shitty mood?), they decided you needed more hassles...

Oh no; haven't you heard? Non functioning numberplate lights are a leading cause of serious & fatal accidents in Australia!

:rolleyes:

Edited by Daleo

Its just discrimination- nothing new. How often do you hear about Grandmas old ford lazer being pulled over and defected for worn out brakes, oil leaks, headlight out, flogged out shocks etc etc.

I've heard of a import driver pulled over and they couldn't find anything, so they defected his handbrake for too many clicks. :wacko:

A dead number plate light and an apparent oil leak.. I can't see an oil leak anywhere...

Every time I come up for Rego-check at one of my rear number plate lights are dead. Two weeks ago it was both.

I asked why they're so fragile and the mechanic said,

a) it's the way you put your tailgate down (since it doesn't seem to happen on my GTR)

b) the filaments are more delicate than they used to be (coming from such n such a place)

Every time I come up for Rego-check at one of my rear number plate lights are dead. Two weeks ago it was both.

I asked why they're so fragile and the mechanic said,

a) it's the way you put your tailgate down (since it doesn't seem to happen on my GTR)

b) the filaments are more delicate than they used to be (coming from such n such a place)

Terry, I replaced mine with SMD versions, nice white light; so much more resistant to that kind of damage.

They cost peanuts on eBay, and last forever.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
    • Noted. Have noticed BMW are more 'high maintenance' for sure. They've attracted my attention as I think the used car prices seem reasonable vs other options, and the extra quality overall vs a commodore / camry / corolla or similar of the same vintage is appealing, especially the interior, and they are more on the sporty side whereas the others mentioned can be more cruising or economical A-to-B only.
×
×
  • Create New...