Jump to content
SAU Community

Recommended Posts

A little bit going on this week; had a new mirror painted to replace the damaged passenger side one (thanks Iain!); while I was at it also had my painter colour code the headlight eyebrows that I've had sitting in a drawer for almost a year now (thanks Mark!).

I don't mind the look, but I'm going to wait until after my mate details the car before I decide whether they're going on. This should be happening within the next few weeks.
Off to grab a new set of tyres later this week, and I'll finally be fitting my camber/toe bolts to minimise some of the rear tyre wear.

Also about time I did a diff oil change; not that impressed with my last LSD oil choice; does anyone have a recommendation?

I was either going to try the Nulon; http://www.nulon.com.au/products/Gear_and_Differential_Oils/Full_Synthetic_80W-140_Heavy_Duty_Limited_Slip_Differential_Oil/#.VAXOk_na7Lk

Or Castrol Syntrax Limited Slip 75W-140.

Any other oils I should be looking at?

I would use the Castrol, just because that's what I've been recommended through award gearbox.

They weren't very positive about the Nulon product, however that was more to do with how the product reacts to excessive heat. I've got some nulon in the open diff in the stagea, it hasn't blown up yet... Lol however I dumped it out of the 180.

  • Like 1

What a bargain! Where from?

from fle bay mate. They are dirty as he'll need a good scrub down and condition but other than that all is perfect need a resistor on the passenger side seat for the airbag plug and just need to open up the seat belt buckle and shave down the inside latch as are seat belt cards are thicker than the 350z's then all is a charm heated switches work as does the electronic forward back adjustments just the up and down are now manual but no biggie. You score a nice little side pockets on the seat wich now catches my phone when I fall out my pocket, it use to just slide under the seat and would be a pita to find. ;-)
  • Like 2

from fle bay mate. They are dirty as he'll need a good scrub down and condition but other than that all is perfect need a resistor on the passenger side seat for the airbag plug and just need to open up the seat belt buckle and shave down the inside latch as are seat belt cards are thicker than the 350z's then all is a charm heated switches work as does the electronic forward back adjustments just the up and down are now manual but no biggie. You score a nice little side pockets on the seat wich now catches my phone when I fall out my pocket, it use to just slide under the seat and would be a pita to find. ;-)

My biggest question is "where are the damn pics!"

  • Like 2

Mate very nice actually hold in in well wich was the main reason I wanted to try as with the stock seats if you take a corner fast and hard I'd end up on the passenger side 8-) the sit lower as well the passage is really low though to low infact so spacers are needed icon real the peddles perfectly just allowed a nice fit!

Got my car back on Friday after the exhaust wheel tried to make an escape a few weeks back.
post-128502-0-40750000-1410092384_thumb.jpg

Turbo was sent off to Hypergear for a Hiflow, just the smaller "G1" profile.
post-128502-0-48030200-1410092663_thumb.jpg

More bad news, exhaust was on it's way out. Cat in the dump was pretty stuffed and rust was starting to eat the rest (the rear section was pretty bad). So some presents from Scott were in order.
post-128502-0-97307100-1410093184_thumb.jpg

And a Blitz Nur Touring cat back to finish it. Selected mostly because of the time frame, it's nice and quiet which I wanted so it worked out nicely.
post-128502-0-79626700-1410093371_thumb.jpg

While it was in having this done I also had the cam cover gaskets done, the passenger side was pissing oil everywhere and apparently had a ton of sealant around it.

Big thanks goes to R&D Mechanical for doing the work, excellent work and very helpful. And a big thanks to Scott for fabricating the dump and front pipe and getting them too me very quickly and Stao at Hypergear for hiflowing the turbo.

  • Like 4

Got my car back on Friday after the exhaust wheel tried to make an escape a few weeks back.

attachicon.gifbrokenturbo.jpg

Turbo was sent off to Hypergear for a Hiflow, just the smaller "G1" profile.

attachicon.gifexhaust.jpg

More bad news, exhaust was on it's way out. Cat in the dump was pretty stuffed and rust was starting to eat the rest (the rear section was pretty bad). So some presents from Scott were in order.

attachicon.gifdump-front.jpg

And a Blitz Nur Touring cat back to finish it. Selected mostly because of the time frame, it's nice and quiet which I wanted so it worked out nicely.

attachicon.gifCatback.jpg

While it was in having this done I also had the cam cover gaskets done, the passenger side was pissing oil everywhere and apparently had a ton of sealant around it.

Big thanks goes to R&D Mechanical for doing the work, excellent work and very helpful. And a big thanks to Scott for fabricating the dump and front pipe and getting them too me very quickly and Stao at Hypergear for hiflowing the turbo.

Good work! Dyno chart?

Did my second oil change on my PNM35 over the weekend, happy to say it hasn't used a single drop of oil in a bit over 3 months. That was Penrite HPR10 which I discovered had been rerated (wtf?) to a 10W50, so I found some 5W30 on sale over the weekend, I thought I'd try it and see if there's any noticeable difference in fuel economy or performance.

Meanwhile the Commodore only had 2.5 litres left in it over the same period and had spent most of that time sitting still...sigh.

Not much new with my stagea.

Decided to paint my wheels gloss black instead of satin black, which i thinks a lot better.

was also considering getting a new rear bar, was thinking dolphin but i dunno. i have a tow var for the stag as i use it to tow our bikes etc so unsure at the moment.

post-107907-0-70566600-1410131982_thumb.jpg

post-107907-0-97631200-1410132078_thumb.jpg

post-107907-0-08119400-1410132124_thumb.jpg

Had a life f**king moment when car wouldn't kick over this morning... Tried to start it twice but wouldn't happen.

Thought straight away to look at the battery and BAM!

2014-09-08080139_zpsc2cbebb5.jpg

So did the usual "stick ur finger in the hole", there isn't anymore water but it needs a serious clean in there.

Gave my headlights a bit of a restore with the Turtle Wax kit.

post-135423-0-37050600-1410435305_thumb.jpg

post-135423-0-80978000-1410435337_thumb.jpg

Now the cracks show up real good!

So I thought I would cover some up with my home made, sheet aluminium eyelids.

post-135423-0-66504800-1410435509_thumb.jpg

My 4 year old daughter says they make the car look cranky! Win!

Painted using Supercheap Auto's Colour Spec paint.

Not a bad match, might even have a go at my roo damage unless someone has a red front left door and fender they don't need?

  • Like 2

Gave my headlights a bit of a restore with the Turtle Wax kit.

attachicon.gifHeadlight Before.jpg

attachicon.gifHeadlight After.jpg

Now the cracks show up real good!

So I thought I would cover some up with my home made, sheet aluminium eyelids.

attachicon.gifHeadlight eyelid.jpg

My 4 year old daughter says they make the car look cranky! Win!

Painted using Supercheap Auto's Colour Spec paint.

Not a bad match, might even have a go at my roo damage unless someone has a red front left door and fender they don't need?

feel like making some more eyelids mate? ;-)
  • Like 1

Well, hit the key in the Dayz and it started first kick. It has been a long haul since 8/12/2013 when she arrived on a trailer with a blown motor.

I have converted to RWD.

There are still a few things to get. A radiator and shroud. And a windscreen. They will come soon.

Can not explain how stoked my son and I were when it started first kick.

  • Like 1

feel like making some more eyelids mate? ;-)

A bit too time consuming, might be a bit quicker second time around but don't think I could do them any cheaper than the plastic ones you can get.

Glad you like them though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Actually,  just remembered there should be info in the threads (somewhere) about swapping to a manual steering rack and deleting power steering all together. 
    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
×
×
  • Create New...