Jump to content
SAU Community

What Have You Done To Your Stagea Lately?


Hanso

Recommended Posts

did you increase boost when you did the tune?? the boost could push the BOV open and assist with venting the air through the valve

could be right. mine was at 17psi tuned i think previous to my boost issue. and wasnt doing it..

Link to comment
Share on other sites

gave it a spray with WD40 and this improved the opening of the BOV and reduced the noise.. :)

well i know what im doing tonight :)

as iaiana said, by how much.. perhaps another sound clip?

Link to comment
Share on other sites

going over the stagea getting it in "ok" condition for mondays track day. my track car wont be back from the tuner in time so have to track the stag for the final time.

found my front rhs driveshaft is leaking a right royal mess. changed out the filters, re-bleeding brakes atm with some quality brake fluid.

Link to comment
Share on other sites

i now have a working horn!

and i changed my parkers and rear numberplate lights and interior lights to LED. interior ones arent as bright as id like. i might get some ebay ones as jaycar didnt have the best range

Link to comment
Share on other sites

ok cool thanks! where abouts did you get them from?

i think ill be doing an HID conversion to the fiat too. Anna likes how bright the 55w 6000k xenonx are in my car :)

Link to comment
Share on other sites

I changed my exhaust today from the Raizer muffler that came on the car to a Fujitsubo Legalis Cat back system that I picked up on Ebay for $600.....

OMG!!! The performance difference is MASSIVE.

So.......I had a look inside the old muffler.........do you think this might have been restricting flow a little ?

88f51aa0.jpg

e867c753.jpg

10172da0.jpg

Link to comment
Share on other sites

Was driving down to Canberra on Friday with my trailer in tow and had to make a road side stop to remove the Grub screw from the BOV. It made the car damn near un-drivable with grub screw in. Car was staggering and shuddering every time I lifted the slightest bit off the throttle.

Will be doing some more work on Wednesday on the BOV with some silicon spray that I hope will improve the performance of the BOV.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
    • Hello, I am looking to replace my two rear drive shafts in my R34 N/A Skyline but I'm finding conflicting information. Do S13/S14/S15 or R32 NA/ R33 NA fit? https://justjap.com/products/gsp-premium-rear-drive-shaft-l-h-nissan-silvia-s13-s14-s15-3x2-type?currency=AUD&srsltid=AfmBOoqY7EwDaYCUoUU3mxxZ_qrUXkVVHiV4MIN7ozoar6scjnEiekv- would this fit?
×
×
  • Create New...