Jump to content
SAU Community

Recommended Posts

R34 PARTS...THE BODY IS AT THE SCRAP YARD AND THIS IS WHAT'S LEFT

OPEN TO OFFER BECAUSE I WANNA CLEAR THE YARD WILL SWAP PARTS I HAVE FOR SALE

FOR THE ITEM'S LISTED AT THE BOTTOM OF THE PAGE.

>DUMP PIPE (ADVANCED) $80

>AIR BAR STEERING WHEEL $150(MANUAL)

>DRIVERSIDE DOOR WITH GLASS $250

>DRIVERSIDE MIRROR $50

>REAR WINDOW (REMOVED) $150

>DRIVERS DOOR TRIM $100 (HAS WINDOW SWITCH STILL)

>R34 STOCK AIR BOX DAMAGED $50 (ONE CORNER & ONE TAB)$50

>A/C COMPRESSER $100

>A/C CONDENSER $50

>ABS MODULE $100

>BRAKE MASTER $150

>DIFF $200

>REAR BRAKES COMPLETE $400 AS IN PIC)

(lower control arm is bent on one side)

>TAILSHARFT $100

>CLUTCH MASTER $50

>PEDALS $100

>HAND BRAKE HANDLE $50(WITH FRONT CABLE)

>STOCK STRUT BRACE FRONT $25

>IGNITION BARRAL/DOOR/BOOT LOCKS AND A KEY $100

>R34 FRONT CROSSMEMBER $150

>BONNET CABLE/LATCH AND HORN PEICE $50

>R34 CASTOR RODS STOCK $50PAIR

>SR20DET 5 SPEED GEARBOX GOOD CONDITION $350

>HIGH FLOW CAT $100

>Vertex Body Kit to suit lancer 96-03 Coupe (full kit) $500

>DECAT PIPE $50

AND THESE ARE THE ARTS I NEED AND AM WILLING TO SWAP PARTS PLUS CASH FOR THEM..OR IF YOU HAE THESE PARTS CHEAP PM ME.

SR20DET RED TOP/S13 SILVIA

1.GREDDY PULLEY KIT (MOST IMPORTANT AND URGENT)

2.GREDDY/HKS CAMS

3.HKS FUEL RAIL

4.NISMO FPR

5.550CC INJECTORS

6.S13 BN BODY KIT......FRONT / SIDES / REAR

Link to comment
https://www.sau.com.au/forums/topic/349323-r34-parts/
Share on other sites

  • 1 month later...

Hey buddy, im after some parts for an R34, here's a link to what i need so if u have them do let me know.. -> http://www.skylinesaustralia.com/forums/topic/355141-r34-gtt-rear-seat-belt-and-front-indicator-holder/

Cheers

Link to comment
https://www.sau.com.au/forums/topic/349323-r34-parts/#findComment-5694622
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...