Jump to content
SAU Community

Recommended Posts

Hey everyone,

last time i was at eastern creek i was told that the helmet i have is longer up to aussie standard and was told before i go back next time ill need a new one

now what i wana know is where in the wollongong/ sydney area is the best/ cheapest place to get motor sport helmets from?

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/
Share on other sites

http://bikegearwarehouse8-px.rtrk.com.au/mx-gear/Mens_Motorcross_Helmets

or goto your local bike shop...they always have specials

eg today i got my carbon/kevlar MX helmet for 150bucks

basic open face helmets can be had for 80bucks but they are heavy and..... well shit to be honest

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5624891
Share on other sites

Hey everyone,

last time i was at eastern creek i was told that the helmet i have is longer up to aussie standard and was told before i go back next time ill need a new one

now what i wana know is where in the wollongong/ sydney area is the best/ cheapest place to get motor sport helmets from?

Does it have as AS sticker on it? What brand/model and how old?

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5624919
Share on other sites

Does it have as AS sticker on it? What brand/model and how old?

+1, what standard is it that was knocked back?

CAMS helmet requirements are here: http://www.camsmanua...dule_G_Q111.pdf

importantly, it includes the following:

4.8 Moratoriums

(a) There is a moratorium on the implementation of any changes to apparel requirements, save for any identified and pressing safety related requirements which may arise or become evident, for non-international events, until 31 December 2012.

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5625306
Share on other sites

It's been like that for ages and It's all pretty clear on their website:

Helmet Standards approved for Race for Real Off-Street Meetings

Drivers Drivers of vehicles slower than 10.99-seconds (1/4 mile) are permitted to use any helmet (full-face or open- face) meeting one of the following Standards:

• SNELL SA2000, SA2005, SFI 31.2A (USA)

• SNELL M2000, M2005, SFI 41.2A (USA)

• BS 6658-1985

• AS/NZS 1698:2006 or AS/NZS 1698.

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5625690
Share on other sites

yeh i never knew that when i went up last time coz before that i had never had a problem and helmet is still in basically new condition.

but anyway im going to make a trip up to the place in auburn in the next week or so

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5625943
Share on other sites

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • You're retired Mark, on bin night, go for a walk, kind of like you're doing the beep test. Put one rock in the first neighbours, come back, get another rock, go to the second neighbours, repeat over many weeks. All rocks eventually gone...
    • No chop chop of anything mate, it is what it is, plus, I don't want any air that isn't either going through the cooling stack or intake getting into the engine compartment increasing under bonnet pressure  Yeah, the Mazda Speed aftermarket intake above is less than ideal for multiple reasons, the requirement to remove the bumper every time you need to service the filter, and also smaller in diameter than the NC1 OEM one Weirdly, Mazda Speed is part of the Mazda motorsport division, "form over function" and $$$$$ for Mazda from unsuspecting punters I suspect  After some googling about them it seems they added no power, but do increase some induction noise Meh In other news, the electricians have been busy today at the house, and are back tomorrow finishing up all the security stuff and exterior lighting, they also added some lighting on the garage ceiling, which will come in handy when working in the garage when it's not freezing out there My Birdies raised garden bed also arrived today as well, which I'll put together and place tomorrow, it's a big tall Bessie, 74cm high, 92cm wide and 214cm long, this will come in handy as I am starting to get "stockpiles" of good soils from doing landscaping, some of the clean rock, namely the river stone, will go into the bottom of the bed for drainage, as well as the old Apricot tree that was out the back,  and when it's full, I'll grab another one, I will be growing enough veggies to keep me both busy as well as supplementing the shopping list I'm also awaiting another quote for a new Colourbond front fence, as the "1980 style cemented in rock edging" that was there and "fashionable at the time" looked arse, and my god, the amount of cement used to fix the rock was insane, it took 1.5 days for me to break out 12 meters of the stuff by hand, trim the bushes back to the fence line and dump it out the back of the joint to deal with at a later date,I will soon need a skip bin to tip it all Unfortunately they did alot of the cemented in rock around the joint, which I hate, so a few pallets of retaining wall blocks for around the front and back where the cemented in rock is will be required to bring it up to a standard, and look, that I will be happy with 12 meters worth of rock and cement Finished smashing the fence line and ready for a fence to be installed, yes, the lawns need some TLC and thickness, the previous owner trimmed the grass to the roots 😢, the TLC I can provide, and nature over time will do the rest And there's probably about another 40 meters worth of this landscaping abomination left to do around the front and back gardens, I'm guessing maybe 3 or 4 tons worth, tip fees for this will be a killer Meh, all in all I'm having fun and keeping busy, plus, it's good PT
    • If I drove to a typical petrol station, what would my choices of fuel be? 
    • Just cut the bottom of the guard out. It's no longer got a big duct, to a sealed box, or a restriction. It has all the cold air from outside. Also, that cai you showed looks terrible. Bends are NOT good for go gos!
    • Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 🤔
×
×
  • Create New...