Jump to content
SAU Community

Recommended Posts

I've been thinking about fuel for my rb30. I was going to go e85 but we can't get it at the pumps where I'm at. I was going to ship it by the barrel, fill up for races(time attack, drag, HPDE, etc), and use pump gas for the street.

BUT! If I'm going to be shipping fuel and making an alcohol safe fuel system, why not use methanol? According to my math, even at 75/25 meth-to-pump it should make more power than E85. It should also run cooler, be easier to find (lots of drag cars here,) and be cheaper.

Anybody gone done this road before?

Interesting fact- in china, where corn is expensive, flex fuel vehicles run M85!

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/
Share on other sites

Nobody has any experience? I keep looking around and all I'm finding is a lot of bs about methanol being dangerous and toxic. It's actually less dangerous and toxic than gasoline.

I think the only reason it isn't used is because Injectors large enough to use methanol and still idle and run normal only recently became available. (id2000)

Unless someone has a good reason not to do it I'm gonna give it a shot.

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5630372
Share on other sites

I can add that buying E85 at the pump will only give many inconsistent results.

Preferred race fuel is C16 or Aviation fuels as they prove to be more stable throughout the year.

As for Power, Methanol makes a bigger bang but more costly to obtain. You will require some form of license in most developed countries.

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5630563
Share on other sites

I've been thinking about fuel for my rb30. I was going to go e85 but we can't get it at the pumps where I'm at. I was going to ship it by the barrel, fill up for races(time attack, drag, HPDE, etc), and use pump gas for the street.

BUT! If I'm going to be shipping fuel and making an alcohol safe fuel system, why not use methanol? According to my math, even at 75/25 meth-to-pump it should make more power than E85. It should also run cooler, be easier to find (lots of drag cars here,) and be cheaper.

Anybody gone done this road before?

Interesting fact- in china, where corn is expensive, flex fuel vehicles run M85!

What is the engine built for? Compression, expected boost, is it intercooled, what is the injector location?

Edited by rob82
Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5630810
Share on other sites

I can add that buying E85 at the pump will only give many inconsistent results.

Preferred race fuel is C16 or Aviation fuels as they prove to be more stable throughout the year.

As for Power, Methanol makes a bigger bang but more costly to obtain. You will require some form of license in most developed countries.

Pump e85 is fine provided you tune for the variations. We can match c16 but @ $1 a litre....

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5630944
Share on other sites

If you are talking about E85 vs meth, why not go WMI? You get pretty much the same power boost as you would when tuning for E85 and the methanol cooler running = the best of both worlds. And you won't use much unless you are boosting, don't need huge injectors, can run on pump fuel everywhere, don't need to upgrade any fuel lines or systems and there are some great packages out there for it. Plus you can vary the amount of meth by juggling with nozzle sizes and multiple nozzles. It is on tap just waiting for you to boost it!

As an example I used probably 100-150ml in 400km of highway driving and I have a 3.5 litre reservoir. I know that when you race with it it is used heaps more, but you can top up between laps etc.

And mixed 50/50 WM in a container is pretty much inert.

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5631965
Share on other sites

One bad thing I've seen with methanol is it burns with almost invisible flames, though E85 could be the same.

All those burnout cars that run it seem to set their tyres and half the track alight though. I also saw an evo with big cams shooting 1m flames on the overrun after it supposedly had been tuned, whether this was the car or the fuel I do not know.

Anyone know more ?

Edited by Rolls
Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5633915
Share on other sites

One bad thing I've seen with methanol is it burns with almost invisible flames, though E85 could be the same.

All those burnout cars that run it seem to set their tyres and half the track alight though. I also saw an evo with big cams shooting 1m flames on the overrun after it supposedly had been tuned, whether this was the car or the fuel I do not know.

Anyone know more ?

The 15% fuel in the methanol would cause the flame to be visible :)

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5633942
Share on other sites

BoostedR's build data from the -5 vs GTRS thread

I have built a RB31/26DETT 824hp -engine hp

264 9.8 HKS

Tomei Dumps

3" x 2 (no mufflers)

530ft lb @ 2800rpm

22psi max

Garrett -10's

Ported std manifolds

BP98 with 10% methanol

Motec

That result proves you can lean on the engine a lot more with just 10% methanol. A water/meth injection setup would produce a similar result.

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5633983
Share on other sites

I have an aquamist hfs-6 on the car right now. It works good but won't give the same performance as mixing meth. It's also something else to break at the track.

The 15% gasoline is supposed to add color to the flame also. I might try a 50/50 mix and move up from there.

Link to comment
https://www.sau.com.au/forums/topic/350574-methanol-vs-e85/#findComment-5634225
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AFM looks to be a z32 The injectors maybe old Nismo 555cc The turbo tag when looked up seems to be a gt2871 , imagine it would have the bigger rear housing .82 all look like the mid 00's mods when he started building it up. Vac hose seems right but would need to see a diagram. Great work going up there and sorting it out, be a good club car for someone wanting a good reliable rig.  I know I would like to have it but no space and too many other race cars at the moment.
    • Heys guys I got a r32 gtst speedo is out by 10kph seems the faster I go the more it be out  just seeing if anyone else had to problem and knows how to fix it 
    • I can't agree. If we hadn't all been brought up with the noise caused by the inefficiency of an ICE, no-one would actually ask for all that. An EV is like any other car, it just goes better. 
    • 2 more things I have to work out Easy one first...can anyone describe how to pull the fuel pump and sender from a 33? I can feel there is some sort of mount and clips but don't have a manual and don't know the trick......if not I'll spend some quality time in the boot witha lighter tomorrow. Second question is harder.  He had changed the upper plenum to a plazmaman but clearly got to a point with the vacuum hoses where he said "f**k it, I'm going inside for a beer" and never came back to that job because it was a mess. Am I right to think that I need: 1. Pre throttle (16mm nipple on inlet) to AAC's main 20mm fitting as the main pre throttle feed 2. ACC has a second 13m outlet joined to that 20mm fitting which I think is the pre throttle air supply for the cold start valve? 3. Cold start valve's outlet fitting then goes to Plenum (to bypass throttle?) There is some adapter on the back of the ACC with 2 fittings (13mm and 10mm), do I run the 10mm through a 1 way valve to the Brake Booster (4) and the 13mm back to a 13mm nipple on the Plenum as the Idle control (5)? 6. Run a 6mm vacuum line from the Turbosmart BOV to the Plenum? 7. Run a 5mm vacuum line from the Fuel Pressure Reg to the Plenum? 8. Run a 5mm vacuum line from the Turbosmart Boost controller to the Plenum? (Wastegate already has a pre turbo pressure source running to the solenoid then the wastegate on the other side of the bay)  Any help appreciated, the GTR is quite different setup and while the Stagea also has FFP it is different again. (And no Dose, I'm not pissing it all off and putting a ethrottle on it....)
    • OK, onto some questions to try and speed up the process a little. Does anyone know what core this Garret is? I know it is a high flowed standard turbo but nothing else about it. Tag says OK 0169J - 446179-5032 Same question for the injectors, I don't know what they flow and ideally can work it out before it hits the dyno, they are a mustard yellow side feed
×
×
  • Create New...