Jump to content
SAU Community

Recommended Posts

Hi

clean out my garage

R34GTR Rear bumper

$850

R34GTR Nismo 320km dash

$800

ARC airbox (brand new)

$700

Nismo front bumper in Blue

$750

Ganador Titanium exhaust system

$1400

Kakimoto Cat back exhaust (use 1 week. too quite and change to HKS)

$900

Located in QLD

Link to comment
https://www.sau.com.au/forums/topic/350608-gtr34-parts-for-sale/
Share on other sites

  • 3 weeks later...

just wanted to say the ganador titanium exhaust is a amazing exhaust currently have one fitted in my car , on idle it sounds very quiet and stock wont get any defects for the noise , once you step on it a bit it lets out a amazing screaming roar.

  • 3 weeks later...

Interested in the r34 titanium exh

where in qld ru?

send pics to [email protected]

Ross

0418 416 921

Hi

clean out my garage

R34GTR Rear bumper

$850

R34GTR Nismo 320km dash

$800

ARC airbox (brand new)

$700

Nismo front bumper in Blue

$750

Ganador Titanium exhaust system

$1400

Kakimoto Cat back exhaust (use 1 week. too quite and change to HKS)

$900

Located in QLD

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...