Jump to content
SAU Community

Recommended Posts

Hey Guys just bought a stock (aftermarket Pod and Cat back) R33 95 with 144000kms on it.

Its pretty clean but now when I idle it revs up and down and occasionally stalls. Other than Idle the car runs extremely smoothly and pulls fine.

rb25detclip1.jpg

My house mate disconnected and reconnnected this hose (in orange circle) and it ran fine for about 5 mins before falling back to the old problem, any ideas on what the problem is?

Thanks heaps for the help guys, really happy with the car except for this.

Link to comment
https://www.sau.com.au/forums/topic/351135-new-r33-hunting-idle/
Share on other sites

does the idle change when u move the steering wheel? If so, try cleaning the AAC valve, there's a tutorial on these forums

Nah doesnt affect it when I move the steering wheel, also gave the aac valve a good clean with carby cleaner and it didn't fix it, perhaps the valve itself is stuffed?

  • 3 months later...

is the factory bov recirculating still if not that will be your problem because factory bov spring to weak and leaks pressure when run to atmo

The spring isnt all that weak.. it will handle 300rwkw.

It is designed to leak at idle, so it leaks regardless of whether its plumbed back or not.

Id say that it isnt though. And because its leaking that air its overfuelling.

That, or the car is saying FUUU to all that silicon spray. haha.

  • 2 months later...

regardless of weather it fixes prob or not change

the fuels filter also clean the hot wire inside ya afm

if its dirty it will make a huge difference

also check the butterfly in the intake as it can get

a carbon build up and not seat properly in the intake

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah it factory manual not sure about ratio but it looks like there’s been some work at the rear 
    • so I need a new speedo cable 
    • Throwing my spoon to the soup here a bit.  When I installed a 044 back in 2012, along with the direct power mod, the car became very difficult to start. To a point I burned one starter motor as I was late for work and tried to get the thing going. With some tuning and careful use of gas pedal when cranking it became bearable. Trying to make this short as possible, but the 044 died after 2-3 years, after which I went with an AEM 320lph pump, which also died after about 4 years to my dismay. After that I went with a Nismo pump, and while trying diagnose an emissions problem, I noticed for the first time that my fuel pressure was 5bar/72psi on idle, and that removing the vacuum line did nothing. After monitoring the situation, and removing the direct power feed and going back to FPCM in attempts to remedy it, I noticed there was fuel in the pressure regulator vac line. Kept the FPCM, installed AEM external regu and the car became sooo much better in every way, including starting. And I had driven it like it was for 11 years.. Anyway, I agree these are likely two different problems, and the FP problem you just haven't noticed before. I do not know much about haltecs, but what first came to mind was the CAS, which probably is not there any more. So how is the wiring from haltec to gauge cluster? How is the battery voltage and alternator?
    • Your car was auto before? You have different diff ratio (auto vs manual i think? or n/a and turbo?)
    • +1 for getting a screen off alibaba, CarPlay/Android Auto is vastly better than whatever navigation cars had 10 years ago. I got an Android screen for my 2015 BMW, huge difference. Fully compatible with factory stuff including iDrive controls.
×
×
  • Create New...