Jump to content
SAU Community

Recommended Posts

I use a Magnafuel washable filter. Methanol/Ethanon compatible.

I tested the local Caltex last week and can confirm they are still supplying E75. Hence im sticking with the United stuff (E90).

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

How easy is it to retune for a massive change eg E70 to E90, can you just do a rough across the board adjustment and accept it will be good enough, or does it really need to go on the dyno?

How easy is it to retune for a massive change eg E70 to E90, can you just do a rough across the board adjustment and accept it will be good enough, or does it really need to go on the dyno?

I didn't find the change that severe although I only changed from the Southland Manildra e85, 1 afr on the wideband richer. I guess you could fiddle with injector size if you have a wideband, just run it a little rich just in case.

I did find extra power though when I tuned for Eflex, just wondering if the ethanol needs a little petrol kick to get it firing quicker in the chamber. As Trent has said, its like C16 straight from the pump, at $1L.

  • 1 month later...

I recently got my car tuned by Gavin Wood

RB25 with GT3076 0.82 external 50mm gate.

Gav said he couldn't get more than 250kw at 1.1bar out of it safely. When I asked why, he said it's probably just because it's an older worn engine with alot of carbon buildup.

If I was to grab some big injectors and swap to E85, would that overcome this problem to a certain extent, and allow me to run more boost/timing to get more power out of the car, or would that just be asking for trouble?

Thanks guys!

I recently got my car tuned by Gavin Wood

RB25 with GT3076 0.82 external 50mm gate.

Gav said he couldn't get more than 250kw at 1.1bar out of it safely. When I asked why, he said it's probably just because it's an older worn engine with alot of carbon buildup.

If I was to grab some big injectors and swap to E85, would that overcome this problem to a certain extent, and allow me to run more boost/timing to get more power out of the car, or would that just be asking for trouble?

Thanks guys!

It would only be asking for trouble if you upped the boost a heap, just filling with e85 and remapping the fuel would make the tune much safer as there is no chance of detonation, and the 30% extra fuel volume will cool the pistons more. I don't see a down side at all other than finding a local servo. Dual map it though if you can, just as a backup.

Gav said he couldn't get more than 250kw at 1.1bar out of it safely. When I asked why, he said it's probably just because it's an older worn engine with alot of carbon buildup.

How old is old?? Mine is almost 200,000km and at 1.2bar it goes quite chirpily :)

1993 GTST... No idea what real K's are but i'm guessing they are probably around that... I think he said adding more timing didn't seem to make a difference so there was no point?

What sorta power are you getting at 1.2bar?

POST FAIL.... Sorry guys, copy and paste went wrong!!!!!!!!!!!

Edited by 34GeeTeeTee

250rwkw is not too far off for 1.1 bar...

from memory I had ~250 @ 1 bar with the 2835... but i never EVER ran 1 bar

shove 1.3 bar into it and you should see a substantial gain.

did gav try to add more boost, or just more timing @ 1.1 bar?

250rwkw is not too far off for 1.1 bar...

from memory I had ~250 @ 1 bar with the 2835... but i never EVER ran 1 bar

shove 1.3 bar into it and you should see a substantial gain.

did gav try to add more boost, or just more timing @ 1.1 bar?

Listen to this man!

God damnit I want to get tuned for E85 now!!!! I'm running a pissy 17psi (dropping to 16) on 98 :( I'd love to up it to 19psi on e85....stop bumping these damned threads! you're giving me bad ideas

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...