Jump to content
SAU Community

Recommended Posts

Clearing out the shed, pre-empting the sale of the Stagea.

I'm sure we've all seen videos like this:

Bought these lights to have a go at a DIY LED tail light project but don't have the time/patience/passion to continue with it. I got as far as removing the back from one of the inner lights and gathering a couple of wiring diagrams from Japanese owners - have included the one I can find on my pc in case anyone wants to have a go themselves. I have 4 sets in total, with the plan being to start modifying the poorer lights and work my way up to a mint (and amazingly cool) set of perfect condition lights.

All lights are located in Adelaide. Prices do not include the cost of post.

http://minkara.carvi...08809/note.aspx

First set is perfect condition with a factory white boot trim piece too, has bulbs and looms. $350

100_1569.jpg

Second set is also in very good condition, has bulbs and looms. $300

100_1570.jpg

Third set is clean but has a slight scratch to the left hand side inner, has bulbs and looms. $250

100_1571.jpg

100_1572.jpg

Last set is my first trial modifying set. I have dismantled the inner lights and cut out the back of left hand side inner, but you could always just glue it back in place if you wanted a cheap set of lights. The right hand side outer light has a slight crack in the lense. The inner lights have bulbs and looms but the outers do not (use your current ones). $150

100_1573.jpg

100_1574.jpg

100_1575.jpg

100_1576.jpg

p7.jpg

Link to comment
https://www.sau.com.au/forums/topic/353153-series-2-tail-lights/
Share on other sites

  • 2 weeks later...

long shot but are you willing to sell a set of inners only?

may do from the cut set - which one were you after?

How much for shipping to Hamilton, New Zealand for one of the sets.

I've never shipped anything overseas, anyone know how i'd go about it? just use auspost?

I have had items sent to me with Auspost via air mail international but would prefer Express post international as it is tracked. Any shipping company that gives you a track and trace number should be fine. If in doubt theres allways Fedex (usually dearer than the post but quicker).

may do from the cut set - which one were you after?

I've never shipped anything overseas, anyone know how i'd go about it? just use auspost?

both LH & RH inners.. How much including postage to 4017?

  • 2 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...