Jump to content
SAU Community

Recommended Posts

hey dont seem to be having a good run with my car lately!

last few days its been dropping down to 0 revs then going back up while changing gears

and seems like its missing sometimes done the obvious checked hoses and cleaned afm

still doing it any ideas please

thanx

Link to comment
https://www.sau.com.au/forums/topic/354373-stalling-r33/
Share on other sites

well been driving it all week didnt do it at all untill this morning...

10mins into the drive started to run shit and then when going down gears to stop it would stall and hunt up and down

about 5mins after that all whent fine and didnt do it at all for the rest of the day???

any ideas haha

Link to comment
https://www.sau.com.au/forums/topic/354373-stalling-r33/#findComment-5686813
Share on other sites

well been driving it all week didnt do it at all untill this morning...

10mins into the drive started to run shit and then when going down gears to stop it would stall and hunt up and down

about 5mins after that all whent fine and didnt do it at all for the rest of the day???

any ideas haha

Hey Dude,

I had the same problem when pulling up to the lights after dropping down gears... Go to your local car shop and buy some Throttle Body cleaner... I did this today and cleaned all of my AAC and sprayed some in the air box and throttle control... I took my car for a run once complete and now it's fine!!!

Make sure you give all pipes around your air box a good spray and clean!

Good Luck!!!!

Link to comment
https://www.sau.com.au/forums/topic/354373-stalling-r33/#findComment-5696303
Share on other sites

if none of that works make sure your AFM element is clean, if you've had a oil pod filter on it the oil will make its way onto the element, spray with with circut contact cleaner, comes up like new,

i also highly recommend cutting open the box that hold the circuitry on your AFM and check for corrosion on the circuit board and on the 3 pins that lead to the plug,

when i did mine it will full of orange corrosion on the circuit board and on the 3 pins, i had to re solder the pins.

if corrosion is left to build up it will create shorts where they touch.

you can seal the box back up with black silicon window goo, pretty sure silicon based gasket goo would work as well.

good luck

Link to comment
https://www.sau.com.au/forums/topic/354373-stalling-r33/#findComment-5697571
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...