Jump to content
SAU Community

Worn Caliper Piston Or Dodgy Pad? R32 Gts-T

Plan-FAILURE
 Share

Recommended Posts

Plan-FAILURE Rising Star

Plan-FAILURE

Posted
Posted (edited)

Hey guys,

Guess I'm a bit bored and have nothing better to talk about...

When I depress my pedal at a stand still I will feel a bit of a notch in the pedal as i push it down harder and hear a slight clicking sound from the front right.

My first thought was a backing plate had a bit of space between the pad and the piston and upon a hard pump of the brake pedal it would be forced back, flush with the piston.

What do you reckon?

Jimmy

Edited by Plan-B
Moodles2 Grand Master

Moodles2

Posted
Posted

Possibly the sound and feeling (through the pedal) of the master cylinder flexing away from the firewall, very common R32 problem solved with a master cylinder brace.

Plan-FAILURE Rising Star

Plan-FAILURE

Posted
  • Author
Posted

Possibly the sound and feeling (through the pedal) of the master cylinder flexing away from the firewall, very common R32 problem solved with a master cylinder brace.

Sweet dude. One of them is going in soon anyway so we'll see what happens :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Powder coating wheels

      By MBS206 · Posted

      I'm interested if anyone agrees with what you've said, and can give a good reason. Temperature of powder coating should be below any temperature you'd use to alter the wheel structure.  Powder coat typically 200 to 250. Annealing if that's what people are claiming would be occuring, starts at 300, and depending on the alloy, can need even up at 400+.   That's the only part I can think of that could cause an issue that people are believing it's from the rim losing hardness and becoming too soft.
    • MBS206
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By MBS206 · Posted

      Negative probe should be on the cars chassis. Positive on the wire.   Start as said above by unplugging everything (unplug the lights, and switches. Now at the switch, there is a wire from the fuse, to the switch, so out your positive on that terminal. It should read open circuit. If it reads something, especially a stupid low value, the short is somewhere between the fuse and the switch. If that's fine, now put the positive probe on the wire that goes to the headlight (at the switch plug). If it reads stupid low, the fault is from the switch, to the headlight.   Another quick test, is take the whole LED light setup from the left, and plug it into the right side, does it still blow the fuse? If you put the right hand side led light setup on the left hand side wiring, does the left hand side wiring now blow?  If the blowing fuse swaps from right to left doing this, your LED lights are the issue.
    • dyl33
      Powder coating wheels

      By dyl33 · Posted

      Anyone know if it's a problem to powder coat forged alloy wheel centers (Rays/Volk GT-C). some say it's bad and can damage the alloy, some say it's not a problem.
    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      Hey guys, I'm reviving an old post but I'm finally getting around to working on this now. I removed the battery to get a better look at the wires and i traced the wires from the headlight to the fuse box in the engine bay, but the wiring looks fine? The wiring for the R/H headlight is 3 wires and then is bundled up with the large diameter wire that goes underneath the fuse box. I didn't take it apart yet. I know you said that its a short circuit somewhere between the fuse box and the headlight. But could it be the headlight switch on the dash? Also, i pulled out my multi-meter and set it on the Ohms, but i'm not sure where to put the negative probe and the positive probe.     
    • wrxhoon
      WTB R33 GTST Catch Can 2L or Bigger

      By wrxhoon · Posted

      I have a 2 lt in Sydney. It was fitted on a R33 GTR, not used for several years . If you are interested email me on: [email protected] I'm not on this forum much .
×
×
  • Create New...