Jump to content
SAU Community

Recommended Posts

Hi everybody, I'm thinking of purchasing a nonturbo R34 25GT skyline coupe, but most of the ones that I have driven kept touching the speedbump or scraping the front when I exit the driveway, does anybody know if stock skylines would still have such an issue? And is there also a way around it? What is the average ride height of skylines?

Any help appreciated, thanks!

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/
Share on other sites

That really depends on what the suspension has had done to it (lowered springs, coilovers), and what type of kit the car has fitted. My car is reasonably low, and scraped everywhere when it had the Jun kit on it, however with the stock kit back in place I've not touched anything yet.

Thee is a certain set of skill you require to drive a sports car though, which are lower than average.

Welcome aboard :)

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5684877
Share on other sites

The car is most likely lowered, stock skylines with stock suspension (from my experience) dont have any trouble going over speed humps or in and out of most driveways. My car is lowered and i dont have any issues with most speed humps however i do avoid as many drive ways as i can because ill end up scraping my front bumper or side skirts if I'm not extra careful driving out. Best way to avoid scraping is dont enter driveways you know your cars is to low for if you must then make sure you enter and exit the drive way on an angle to avoid scraping where possible.

Lowering a the car also lowers it's center of gravity which in turn improves handling in most cases with upgraded suspension it can also help reduce the vehicles body roll while cornering.

Legal limit is 100mm (10cm) i believe easiest way to check is grab a soda can there normally 12cms and go around the car and see if the can fits.

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5684896
Share on other sites

Thanks for the advice guys =D

Great forum, been looking around for an r33 or r34 but the cars on carsales are all claiming to be under 100000kms but that's quite impossible as some are older than 15 years, it's really sad they discontinued the Nissan skylines, they keep getting more older and older

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5684973
Share on other sites

The best thing you can do is find a Skyline thats been well cared for - look for evidence. Service records, condition, how clean the car is presented can all tell you a story about the owner. If you are buying privately, and get the chance have a look at where the car is kept.

There isn't anything wrong with a few kays (as you said, they are 15+ years old now). My GTS-T has an indicated 158kms on it, and I'd suggest looking at the numbers THATS been wound back too. The thing is, I bought it off a mate (who is also from here). I know how he drives (like my nan), know the mods (very few) and know its been looked after and serviced. It still pulls hard, and has good even compression.

I'm guessing you need a non turbo for licencing purposes? They enjoy a bit of a inflated market, and from what I've seen pretty good resales.

There is a thread on buying them somewhere - find it and have a read.

Good luck mate!

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5685270
Share on other sites

I think the thread Anthony is talking about is this one http://www.skylinesaustralia.com/forums/topic/35129-im-buying-a-skyline-what-should-i-look-for/ i would recommend reading the whole thread to get an idea of what to look for when buying a car in general.

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5685508
Share on other sites

Hi everybody, I'm thinking of purchasing a nonturbo R34 25GT skyline coupe, but most of the ones that I have driven kept touching the speed bump or scraping the front when I exit the driveway, does anybody know if stock skylines would still have such an issue? And is there also a way around it? What is the average ride height of skylines?

Any help appreciated, thanks!

I've a stock height R33 with stock front bar & I've no trouble going over any speed humps or drive ways yet.

It clears them no problem just like the Toyota White Goods (Corolla & Camry) my parents drive.

As to ways around it, either drive really careful (enter all speed humps/driveways at an angle) or get some stock suspension put back on.

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5685859
Share on other sites

Thanks for the advice guys =D

Great forum, been looking around for an r33 or r34 but the cars on carsales are all claiming to be under 100000kms but that's quite impossible as some are older than 15 years, it's really sad they discontinued the Nissan skylines, they keep getting more older and older

They still make them......

Link to comment
https://www.sau.com.au/forums/topic/355003-skyline-too-low/#findComment-5688021
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...