Jump to content
SAU Community

Ignition Barrel/steering Lock Destroyed, What Locksmith Should I Visit?

Rolls

By Rolls,
in South Australia

 Share

Recommended Posts

Rolls Grand Master

Rolls

Posted
Posted

So my car was waiting to get towed and some pricks broke in, snapped the steering lock and stuffed the ignition barrel in the process (once the lock is snapped it disables the start position) then realised half my intercooler piping was in the car and there was no way it was going to start so they flogged the towing money.

Now I'm sure I can locate an ignition barrel myself but I want to get it retooled so it takes the same key as my doors which will obviously involve a locksmith, I figure it is probably best to just go straight to them as it'll be cheaper if they do it all.

Can anyone recommend a locksmith that does this kind of work?

Aberax Grand Master

Aberax

Posted
Posted

So my car was waiting to get towed and some pricks broke in, snapped the steering lock and stuffed the ignition barrel in the process (once the lock is snapped it disables the start position) then realised half my intercooler piping was in the car and there was no way it was going to start so they flogged the towing money.

Now I'm sure I can locate an ignition barrel myself but I want to get it retooled so it takes the same key as my doors which will obviously involve a locksmith, I figure it is probably best to just go straight to them as it'll be cheaper if they do it all.

Can anyone recommend a locksmith that does this kind of work?

A Nissan Service Agent should be able to do that for you, not too sure how much they would charge. When we had to have our Commodore one done, it was about $80-120, just gave them the Key and Barrel and about 1-2 hours later got a call.

Rolls Grand Master

Rolls

Posted
  • Author
Posted

So for $120 you gave them a new barrel and key or you just supplied the key and they set up a new barrel for you to suit?

Just trying to figure out how much I am up for, also by nissan service agent you mean like the spare parts/dealer places?

Cheers for the reply!

Aberax Grand Master

Aberax

Posted
Posted

So for $120 you gave them a new barrel and key or you just supplied the key and they set up a new barrel for you to suit?

Gave them the Key and a New Barrel, the new barrel was about $60-$100, then plus the $120 for them to set the barrel up for the key.

Just trying to figure out how much I am up for, also by nissan service agent you mean like the spare parts/dealer places?

Yes, Spare Parts/Nissan Dealer

Just had a look in Nissan FAST for you, for my R33, the lock is under part section 998 and the "Lock Set-Steering" is Part Number 48700.

post-58049-0-64417700-1298797841_thumb.jpg

JiN_MaN Veteran

JiN_MaN

Posted
Posted

Or just another way of solving it would be buy new barrel and key for not very much and then get an alarm + central locking.

Although the doors will be a different key you will next to never have to use it, plus you get the added bonus of an alarm + central locking for not much for than the cost of a new barrel and cutting.

ps. If you already have an alarm then you can just pretend I was never here.

Rolls Grand Master

Rolls

Posted
  • Author
Posted

I actually already have an alarm and central remote locking however the remote broke and the company that made it went into recievership, I pulled it apart looking for lose connections, dry joints etc but couldn't fix it so had to disable the alarm.

Hilariously I just pulled the fuse out of the alarm module and it completely bypassed it, so a new one is definitely on the cards once this is all fixed.

If it is only $100 to make it use the same key I though might as well do it if the barrel is already out.

D_Stirls Veteran

D_Stirls

Posted
Posted (edited)

From the few cars that i have dealt with that have had their steering lock broken i can tell you that the steering shaft will almost certainly be damaged as well. so you will be up for a compete mew steering shaft assembly

Edited by D_Stirls
Rolls Grand Master

Rolls

Posted
  • Author
Posted (edited)

From the few cars that i have dealt with that have had their steering lock broken i can tell you that the steering shaft will almost certainly be damaged as well. so you will be up for a compete mew steering shaft assembly

What actually gets damaged? Ive actually found that the steering lock is still functional, it just has a bit of slack in it now, but it has obviously broken off in the ignition somewhere. Which is weird because it certainly didn't engage when I first discovered it had been broken into.

Edited by Rolls
D_Stirls Veteran

D_Stirls

Posted
Posted

There is a key way cut into the steering shaft itself, this is what becomes damaged, but if yours it still functioning (be it with slack) then you are lucky but it just makes it easier for the next thief.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R33 general questions

      By joshuaho96 · Posted

      Sounds like the rack seals blew.
    • GTSBoy
      BCNR33 Blower Motor Resistor - Testing

      By GTSBoy · Posted

      ^ This is all good advice. I can imagine that there's some passive components in the HVAC controller that run that PWM output that could die, or suffer bad solder joints. It can be worth opening it up, taking a schmooze around looking for swollen electro caps, evidence of liquid escape anywhere, tracks that have been hot, lifted, cracked, etc. A DMM might not be suitable for seeing if the PWM output is pulsing. Might be too fast and too low voltage for a DMM to keep up. An analogue voltmeter might give a better hope. I use a handheld oscilloscope (<$100 from Aliexpress if you want something cheap). A DMM might see the voltage across the motor flicker. Otherwise, as above. If you can successfully see PWM action, then the control side should be good. If you can't see it with what you have, you might need to step up the instrumentation used, as above. Beyond that, and dbm7's advice on testing the motor directly, you're down to looking for broken wires, corroded connector pins, etc.
    • ChrisGtt
      R34 Gtt RB25det neo Issue After Modifications

      By ChrisGtt · Posted

      So Thanks for the comments etc. To follow up on this, we went down the path of fitting a divider down the middle of the external pipe that was added to the exhaust manifold and the divider went from very close to the external wastegate all the way up to the "V" part where the pipes from each side of the manifold joined. After this modification it was finally in a position to do the dyno-tune with some degree of success. Top end power was down about 10kw (250rwkw down to 240rwkw) I believe from previous but it seems to be more responsive lower down and at least it is now driveable and fun and back on the road to be enjoyed. Apparently the timing couldn't be run the same as it was running into knock and boost was down about 1psi. For all we know this could have been from the fuel being a bit older, or perhaps some slight complication from the new head gasket as we didn't have compression figures from before that mod to compare. I'm no mechanic and this is second hand info but I just wanted to follow-up to those that commented or read the original post with interest. After so many months of stuffing around this is a big win. The interesting part was most of the info around this was gained from information around Barra motors and not GTR as the manifold setup on the Barra with single turbo was more similar.  Thanks for those that helped with info. Regards Rob 
    • dbm7
      BCNR33 Blower Motor Resistor - Testing

      By dbm7 · Posted

      G'day ... first up, I very much doubt that's a resistor network (as used also for this job), but the part# looks right. The description of 'power module assembly' looks to be nissanese for 'PWM driven, ground switched, DC motor speed controller'.... the circuit in the schematic kinda infers that's the case... ...with the transistor symbol appearing in the unit described here as 'Fan Control Amp(lifier)'....being driven by pin20 on the HVAC unit,  and a feedback signal on pin19 from the motor negative terminal for some reason (might be motor fault detection, maybe they detect commutator switching to determine motor revs as well, I dunno)... but if they are  counting commutator spikes, a bad segment (or really worn brushes) will throw a spanner in the works... The motor itself will as said be brushed DC with segmented commutator, rated at 12VDC nominally ~ now-a-days I just unplug them, determine the positive wire, and hook them up to a variable power supply and find out how much current they draw, if they work etc etc ...you can also check for bad segments...ie; set the power supply up to feed 1volt @ 2amp max, then watch the wattage count as you slowly rotate the fan blower motor through a complete revolution ; any bad/dead segments will be clearly evident...some folks would just say determine the positive wire, and feed it battery voltage, and if fan spin, you've got a win...<grin>... well, at least that infers it should do something when plugged back in, and the HVAC unit commands it to run... and if it doesn't, you suspect the module, but you should check the PWM signal on pin20 is actually present, and if it is, blame the module ...  
    • GTSBoy
      Did tie rods. Steering now not "springing" back.

      By GTSBoy · Posted

      Ah. OK. I take it back. I hadn't looked closely at the R33/4 arms and presumed that GKTech did as GKTech do everywhere else, which is to use sphericals there. The poly bushings are made to be 100% interchangeable, should use the standard bolt just fine. Every other bush in every other place in pretty much every other car, does.
×
×
  • Create New...