Jump to content
SAU Community

R34 Spares

boostedr34
 Share

Recommended Posts

boostedr34 Enthusiast

boostedr34

Posted
Posted

have a few spares let over from my old r34 skyline

i got a tiptronic auto gearbox with all the auto parts pedals etc i changed my skyline from auto to manual $650

i have a aftermarket inter cooler and piping to suit r34 rb25neo $350

i also have a to4 turbo i was gunna put on i dunno much about it its rated at 600hp has a t3 flange $500

i also have a rear muffler is aftermarket sounded tuff as $100

i also have a high mount manifold to suit a rb20 with external waste gate $350

msg me if u have any questions on 0413753824 im situated on the central coast about 40 min nth of sydney PICK UP ONLY

post-71356-0-13625800-1298942992_thumb.jpg

post-71356-0-41143200-1298943054_thumb.jpg

post-71356-0-57270700-1298943090_thumb.jpg

post-71356-0-01974500-1298943132_thumb.jpg

post-71356-0-38545100-1298943167_thumb.jpg

post-71356-0-77159600-1298943212_thumb.jpg

post-71356-0-60698700-1298943255_thumb.jpg

post-71356-0-51864900-1298943294_thumb.jpg

Link to comment
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      CD009 RB Conversion

      By Dose Pipe Sutututu · Posted

      Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • tidi0x
      CD009 RB Conversion

      By tidi0x · Posted

      Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • robbo_rb180
      R32 Gtst - Track Car

      By robbo_rb180 · Posted

      If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • 180 wanabe
      370gt Stock Suspension

      By 180 wanabe · Posted

      If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
    • bcozican
      R32 Gtst - Track Car

      By bcozican · Posted

      Id like to race in the US i think alot of those track would suit me   For the s15? Youd be stuck between club sprint and the new Open Am wouldnt you depending on how much interior you have left in
×
×
  • Create New...