Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

some more progress.

secondary injectors will fit, took abit to get them sitting in the rite spot so they dont spray on to the runner and port walls and without putting the hole in the wrong spot to start with.

post-19586-0-94566200-1453540872_thumb.jpgpost-19586-0-17971500-1453540885_thumb.jpgpost-19586-0-26049500-1453540898_thumb.jpg

post-19586-0-65167000-1453540913_thumb.jpgpost-19586-0-11975000-1453540924_thumb.jpg

swaybar will need some modding

post-19586-0-96543300-1453541023_thumb.jpg

had some action in the backyard withe the next doors tree...

post-19586-0-84173400-1453541099_thumb.jpg

  • Like 1

no speed sensors. not really necessary. atmospheric conditions can change the boost given the same comp speed. i will be running a balance pipe on the back of the engine to average the boost to each bank.

just working out the heater/turbo plumbing atm. + water to air cooler plumbing+ our lease is up and have to move.........

secondary injectors all mounted.

It looks schmick, nice job. But why go to staged injection when you can run injectors up to 2000cc that will idle and run nicely down low as well?

If it's bling, I understand. But the work / complexity increase would make me shy away.

  • 2 weeks later...

It looks schmick, nice job. But why go to staged injection when you can run injectors up to 2000cc that will idle and run nicely down low as well?

If it's bling, I understand. But the work / complexity increase would make me shy away.

because i want it to pass an im240 if need be. my ecu can run it, and with proper injector placement i wont need as big. better economy and more consistent mixtures.

ive got a set of moran billet atomisers that will do the job, but i want it done well. fyi the "2000 ish cc" injectors on the market are gas injectors and fail on a regular basis. there not meant for liquid petrol. let alone e85. the rubber seals inside swell and change there dynamic flow rate.

yes some updates. having our lease up sucks. house hunting has taken a front seat over this.

also i am abandoning the water to air intercoolers in the manifolds. the volume is to big and will make it lazy. (i need razor sharp throttle response for the paddle shift that im running.

also bonnet clearance is an issue. i want to raise the engine a cm or 2 for ground clearance. stock sump will be marginal at best,,

ive got some old hypertune s2000 plenum shells i am modding to fit. (shortening and mirror imaging one for the r/h bank)

the water to air coolers will be mounted in the inner guards out of the way.

all but finished my 110L fuel tank. all in 316L so it wont corrode. twin walbro 400's staged and an internal gated surge tank/pot

post-19586-0-09213900-1457252365_thumb.jpgpost-19586-0-20692500-1457252375_thumb.jpgpost-19586-0-53988000-1457252389_thumb.jpg

  • Like 1
  • 2 months later...
  • 6 months later...
  • 1 month later...

getting close. just finding the time has been hard + the 90 odd wires for the engine wiring harness took some time to make.

got the air shift piston and linkage sorted so i can use the stick and have paddle shift.

                                                                                                               DSC_0292.JPG

DSC_0317.JPG

shouldn't get hot with the "super fan"                                                                                                                                                     

DSC_0318.JPGDSC_0293.JPG

 

  • Like 6

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Anyone want to make me an offer to take my v36/g37 3.7l manual coupe in full? Off memory it was low 100k km but the battery is flat so can't tell right now. What's wrong. I had engine problem's that led to a nice clunk. It made it home but it wasn't pretty for the last few kms. Happened under revs. Sounds like bottom end.. never got around to fully checking or fixing it so the car has sat still and unregistered for a few years. Minor bump in front end set the pedestrian protection under bonnet airbag off and that was meant to be repaired, but while waiting for the repair (parts to come) I got the engine problem. The rest of the car is in decent condition. All drive line is good. All interior is good. Leather interior. Wheels in good condition and decent tyres although the ps4s are likely a little too old now it's sat still. Colour of the car is pewter off memory, the dark grey colour. In Camden NSW. Would need a tray back pickup.
    • Anyone want to make me an offer to take my v36/g37 3.7l manual coupe in full? Off memory it was low 100k km but the battery is flat so can't tell right now. What's wrong. I had engine problem's that led to a nice clunk. It made it home but it wasn't pretty for the last few kms. Happened under revs. Sounds like bottom end.. never got around to fully checking or fixing it so the car has sat still and unregistered for a few years. Minor bump in front end set the pedestrian protection under bonnet airbag off and that was meant to be repaired, but while waiting for the repair (parts to come) I got the engine problem. The rest of the car is in decent condition. All drive line is good. All interior is good. Leather interior. Wheels in good condition and decent tyres although the ps4s are likely a little too old now it's sat still. Colour of the car is pewter off memory, the dark grey colour. In Camden NSW. Would need a tray back pickup.
    • I started with the above in my head too, and I might be reading / thinking about what they want wrong, which is why I complicated it a bit further. Purpose I'm seeing is for the corner indicator to be on with headlights, and then if the indicator turns on it can still flash. The relay part above I can see working as required, except in the case of headlight is on, and indicator is on. The change over relay you've wired in would get signal from the indicator, and as it flashes would give power to the globe from the indicator, but as it flashes off, power comes from the headlight, which would cause the indicator to be constantly on when headlight is on, even while indicator change over is flashing. That is unless we don't care if it flashes or not if the headlight is on? I guess that's an OP clarification.
    • HI, Ive got an r34 gtt sedan A/T. The instrument cluster went out and I replaced it with another A/T everything visually looks the same and all the gauges work now with the exception of the speedometer and odometer. The speedo will stay pinned at zero until I'm going about 55kmh and then it'll say Im going about 5kmh. my odometer seems to be tracking at about a 1/10 of what it should. If I go 1km it'll say I've only gone 0.01. Appreciate any and all help. Ive tried searching through the forums reddit and a local fb group. The only info I think I've found is that some cars didnt come equipped with TCS (mind is) and the clusters may be different between those? I've also installed a brand new VSS and no joy obviously. TIA. 
    • what speedo healer did you use?  
×
×
  • Create New...