Jump to content
SAU Community

Recommended Posts

I have pulled my motor out to install some 6Boost Manifolds. I have found some issue's, most expected.

-OEM water and boost hard pipes that run beside the rocker cover don't fit

-OEM twin turbo pipe doesn't fit. I have a hard pipe kit here and will update you all if it works

-Manifolds aren't even. 4mm out. If I hold one up and then tighten I can get it down to 2mm. Not to bad but I hope my Front pipe fits ok

-Both manifolds just foul on the head. I will have to grind the head tabs down as I also need the clearance for heat wrap

There is no doubt these will make more power with better spool over my stainless items. I will be on the dyno to confirm

Matt

Pictures tell the story:

4cf66aa9.jpg

c9b4e905.jpg

8200f9fa.jpg

4d1a93cf.jpg

Link to comment
https://www.sau.com.au/forums/topic/355887-6boost-rb26dettt-manifold-install/
Share on other sites

  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

Diameter wise - whats the internal of the pipe?

Just thinking if it's actually larger, will it hinder perhaps due to lower velocity etc?

The runners are certainly longer ye?

Be interesting to see results. Certainly a pain RE: OEM piping/lines, but given the length of the runners that would be unavoidable regardless

Diameter wise - whats the internal of the pipe?

Just thinking if it's actually larger, will it hinder perhaps due to lower velocity etc?

The runners are certainly longer ye?

Be interesting to see results. Certainly a pain RE: OEM piping/lines, but given the length of the runners that would be unavoidable regardless

The OD is ~42.5 same as my stainless mani's

The also are ~1.7times longer

Any gain will be amplified at my power levels so we should be able to see and get a accurate % for others to make a eductated decision if the install hastle and cost is worth the effort

Edited by BoostdR

Indeed, will be good to see.

1.7x longer is interesting.

Dyno might not show difference when loaded up in terms of response, you'll have to get some seat of pants action going :D

Pics of old manifold by chance?

Indeed, will be good to see.

1.7x longer is interesting.

Dyno might not show difference when loaded up in terms of response, you'll have to get some seat of pants action going :D

Pics of old manifold by chance?

e1312463.jpg

Wow didn't even know these existed. Can I ask:

1) Any dummy fitment done to see how these clear the strut towers etc?

2) the collector pipe - does it not fit by a little or is it just a completely different thing? ie is the hard pipe setup roughly similar in configuration to the OEM stuff, just some minor changes, or totally different? Just wondering if it's achievable for the DIYer (most of my inlet is now custom).

3) sorry if it's mentioned elsewhere, but what are the turbos?

4) is it intended that the mounting position of the turbos would enable the OEM y-pipe to connect up to the dumps? Or is completely different setup required?

1. clearance to the strut towers not an issue

2. No chance of fitting the twin turbo pipe. The hard pipe kit I have routes differently to the OEM..away from the rocker cover

3. GTRS

4. Front pipe is meant to be a direct fitment

post-49288-0-77962600-1299210203_thumb.jpg

You will need to modify your aftermarket 'twin turbo' pipe. The rear will foul the front manifold.

Front pipe will bolt in, no dramas there.

I had an issue with the stock rear o2 sensor fouling. That may have been due to the aftermarket dump pipes though.

Cheers,

Johno

how do you get 4mm out? if so your front pipe will be 4mm out to... in wghat dimention are they 4mm differant?

The turbo flange level (height) when mounted is 4mm different. One is higher than the other.

Update

I have ground about 2mm off my head tabs, now has enough clearance for the manifolds with heat wrap.

The manifold flanges are also threaded, why I don't know. They will have to drilled out to allow the turbo studs to poke through.

I have ordered some black braided stainless line and AN fittings for the water lines. I have also found a -6AN To 3/8 barb to join at the back of the Plenum. I will post up my order list soon.

Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Right, here's a video of the basic operation at least.  This is what you can expect day to day when you turn the car on and it boots from standby.  The only thing from a media point of view I haven't gotten working is for it to autoplay plexamp when it turns on from standby (it works from cold boot) but that's more of a plexamp problem as it will autoplay other music players.  Also attached is my one stray cable.  It's part of the screen's wiring adapters but there's just nowhere for it to go in my car.  I've just now done a bit of research and found a matching port on a 2010-2014 head unit with BOSE.  Mine has no BOSE so that's that case pretty much closed I think.  Plugging in the Infiniti AC panel basically did nothing for me, so that's a dead end as well.  Next port of call is to mess with this CANBUS module and see what I can find from it.  I found this resource containing the DBC files for a 2010+ G37 : https://github.com/icecube45/Dash_InfinitiG37/blob/master/InfinitiG37.dbc I'll now have something to go from when I try to extract my CANBUS data so I can see if the HVAC Mode, Fan Speed, Temperature, etc. match and also the gear shifter position.  It's a pretty big assumption that it's just mismatched CAN signals but considering all the devices in the CAN network are talking to each other (AC can be fully adjusted just with no info on screen) it might be a safe one.  I will report back WhatsApp Video 2025-02-26 at 12.49.10.mp4
    • Thanks for that Paul.  Do you think if I posted a picture you'd be able to remember where it went? 
    • Sorry Duncan, I didn't get a notification for the replies.  Thanks for responding!  It's a full Android device, but does allow you to use CarPlay/AA as well.  This is the one I bought from NaviRS on AliExpress: https://www.aliexpress.com/item/1005006368602668.html?spm=a2g0o.order_list.order_list_main.111.59aa1802JDzQ0E - the 2K 8G-256G CAM variant but it seems to have gone up by £170 since I bought it!  My purchase was £307.14.   It's not the fastest thing in the world but performs perfectly adequately.  It stays on standby unless I disconnect the battery and let it power down, then it's just a fairly standard Android bootup time from cold.  The DSP Equaliser is very nice and made the standard stereo system sound pretty decent compared to the stock screen.  Perhaps I can take a video of it when I get a sec. It *allegedly* supports the reverse camera, but I'm yet to get that working.  It has options for reverse cam (a camera unit can be bought separately) or 360 cameras (also bought separately).  To be fair it doesn't seem to detect that the shifter was put into reverse but I'm working on a theory about this as well.  At the moment I'm going without which is a bit annoying considering the car is an absolute canal barge but so far I haven't caused any damage I'll grab a picture of the wire I'm missing later today when I can get outside.  My theory, by the by, is that not only is the head unit different, but the CANBUS network has different signals for the different years.  I think this because I have a spare AC panel from a newer Infiniti G37 (as opposed to my Nissan panel) which wouldn't control anything except the volume when I had it wired up with the stock system.  I'm going to throw it back in and see if the screen will respond to it.  I've just ordered an arduino CANBUS module so I can have a look at the signals going around the car and see if I can spot anything.  I'm thinking if I can work out what it's expecting vs what it's getting I might be able to translate and relay the signal back but so far just a theory anyway. I also found this on my travels, so far the only one that specifically matches my car: https://www.aliexpress.com/item/1005002822934280.html?spm=a2g0s.imconversation.0.0.33433e5fgttovi If you look at the picture of the before, it has the card reader slot, and the picture of the head unit is exactly the same as the one pictured in my original post.  I asked if they sell the cables separately but sadly they won't.  I didn't want to just buy this one because it's a super old Android version and only dual core - likely slow as hell. 
    • As above, you did refill the coolant and burp the system before running it again didn't you?
    • To be fair - you see the same thing for every clutch. There's always someone making an installation error.
×
×
  • Create New...