Jump to content
SAU Community

Recommended Posts

Hey all. Got a few parts for sale.

First up is a near-new Trust T518Z 10cm complete with braided oil line. It was purchased brand new from Trust Japan via J-Imports by myself and has only done literally 1000km on a track car. Therefore it is in perfect condition; as-new you might say. Only ever used at up to 14psi. Made 240rwkw at this boost with full boost by 3700rpm.

For those that don't know these are a bolt-on turbo for S14/S15 SR20 engines wishing to make 250rwkw.

t518z_1.jpg

t518z_2.jpg

t518z_3.jpg

t518z_4.jpg

Asking $1400.

----------------------------------------------------------------------------------------

Next up is a pair of Tomei Procams to suit S13 SR20. The specs are 260/260deg 12.0/12.0mm. Tomei part numbers: 1431260120 and 1432260120. They were also purchased brand new from Tomei Japan and have done the same amount of kms. There are two small chips on the sides of one of the lobes but there is no damage at all to the actual areas which interface with the rockers.

procams_1.jpg

procams_2.jpg

Asking $330.

----------------------------------------------------------------------------------------

And last up is a Bosch-branded Z32 AFM. This was purchased brand new from Bosch and has done around 2000km. This is not one of those second hand units off an actual 300ZX which are 20 years old and are probably out of spec.

afm.jpg

Asking $230 with plug.

----------------------------------------------------------------------------------------

Parts located in Eastern Melbourne. Can post anywhere in Australia at buyer's expense.

Pm or call me on 0409403769.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...