Jump to content
SAU Community

Recommended Posts

Is the stock boost gauge any use in a R33?

I have been playing round with a bleed valve and nothing I do seems to make the gauge go above the halfway mark.

I know that the unit of measure is very roughly 7 on the gauge is 14psi but does it actually read true at the top of the scale?

All I have done is replace the solinoid with a bleed valve, is there a restriction in the std plumbing that will limit it to the same as the +5000rpm boost level? Because that seems to be all I am getting.

Link to comment
https://www.sau.com.au/forums/topic/35601-r33-stock-boost-gauge/
Share on other sites

I wouldn't rust the factory gauge at all !!

It's way too slow....

Get yourself an after market gauge, even if you just borrow one off a mate so you can tune the bleed.

When putting in a bleed valve, take out all the factory piping for the stock stuff. Put in new pipes and the bleed then tune it. Yes the factory pipework has a restrictor in it to limit things.

The brass restrictor is marked by a white/yellow stripe on one of the pipes.

J

The stock boost gauge is pretty useless. The units are difficult to decipher and it lacks markings. It's slow to respond to changes in boost pressure and will not really read spikes or anything well.

You can get a VDO or Autometer boost gauge pretty cheap.

Thanx for the input guys.

Bought a cheapie boost gauge and it is running about 8 pounds. Getting rid of the solenoid out of the circuit and losing the 2 stage boost has made the car HEAPS more fun to drive and won't have raised the peak power by 1 kw.

Really makes you think that something with a big fat midrange is going to cream a dyno queen on the street don't it?

I found that the only real problem with the standard gauge is its size. Its just physically too small for the human eye to read accurately without markings. Comparing it with my Blitz gauge, the needle has about 5cm to move to reach 1 bar, whereas the stockie has maybe 2.5cm. I've noticed that it is a little slower but moves to a position where the maths suggest it should be (ie the mmHg of stock ~= Bar of Blitz).

Also, I set the boost level on a dyno (more accurate than any gauge) to 13 PSI and the needle sits a few mm below +7 where it should be.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
×
×
  • Create New...