Jump to content
SAU Community

1992 R32 Gtr


Recommended Posts

R32 GTR 1992

I am Selling my Pride & Joy

I Don't have the room to keep it anymore

N1 Rear pods, n Front bar Vents

Ohlins Coilovers with Adjustable Oil Dampner

5Zigen Exhaust System

Nismo Gear knob

Momo Race Steering Wheel

Jap 6 Spoke Wheels

HID Head Lights

Boost Gauge

HKS Dual Stage Boost Controller, not installed

M's Pod Adapters & K&N Pod Filters, not intalled

Sony Mp3 Head Deck

Kenwood 6" Spilts up front & 6" in back

Computer Remapped by Nissan Japan

Only Done 85,250kms

Always Run on Caltex 98

Immaculate Interior

Over $4,000 Spend

UAS 5 Button Clutch

Spiggot bearing & Thurst Bearing

Alloy Radiator

Braided Clutch Line

High Tensile Ball

Machined Flywheel

200 Cell Metalic Race Cat

HKS Dual Stage Boost Controller

New Power Steering Pump

Iam the first Registered Owner in Aus

Rego, 25 Mar 2011

Always Washed, Polished & maintained

It has been a Awesome car, Drove to Qld & Back,

without a Problem

Serviced every 3,000kms with Fully Synthetic Oil

Gear Box, Transfer Case & Diff Oil has been Changed

New Spark Plugs, New Front Brake Pads

Exterior has small rust spot above LR Wheel Arch

Small Dent in passenger door

LF Gaurd has been painted, but not the best paint job..

As seen in Picture Above..

Asking $13,500 but I am Negotiable..

Thanks For Looking...

post-74081-0-94999500-1299365543_thumb.jpg

post-74081-0-54079700-1299365717_thumb.jpg

post-74081-0-67528200-1299365803_thumb.jpg

post-74081-0-58165300-1299366056_thumb.jpg

post-74081-0-13720200-1299366092_thumb.jpg

post-74081-0-55092100-1299366118_thumb.jpg

Edited by Ben GTR
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Yes sir, that was me. Fake ARP's are also a thing over here in Canada and we only order from reputable dealers. It's sad that even simple things like bolts and hoses are now also being copied... anything to make a dollar.  Story time. Like all cheap crap from China, it's even an issue with firearms. Roughly 15 years ago, I purchased a new cheap Norinco 12g shotgun. First time out in the bush with it, while firing, bolt assembly didn't lock and it fired out of battery. The receiver also being cheap steel, basically exploded in my face. I was lucky to be wearing eye protection. Long story short, don't buy Chinese junk. Also Norinco being state run and their only military arms producer, if ever they do try and take over a country, don't worry about it lol. 
    • Installed  Nismo coppermix twin competition spec last year in my bnr32 with pull trans with Oem slave cylinder. The point at where the clutch disengages/enages is right at the top of the clutch pedal, meaning I barely have to push the pedal down for the clutch to be disengaged.  You guys that have the same combo are you experiencing this high pedal bite point??   Secondly I’d like to have the disengagement point lower meaning I have to push the pedal more(further not effort)for it to be disengaged.  I’m thinking to use a Nismo big operating cylinder(bigger bore at 13/16 vs Oem 3/4) which will require more pedal stroke to get the equivalent movement at the clutch fork. But I see Nismo web site says not to mix these 2 as the Nismo big operating cylinder doesn’t have enough stroke to disengage??? Any folks run both the coppermix twin pull with Nismo cylinder??    Thanks in advance for the replies but prefer only guys with pull clutches to respond. thanks     
    • Any chance u could let us know where your based ?
    • That’s a great deal and I would jump on it if you were closer. Melbourne is a bit of a hike for me though unfortunately 
×
×
  • Create New...