Jump to content
SAU Community

Revs Drop When Engaging Gear While Stationary

ClutchBurndout-:(

By ClutchBurndout-:(,
in General Maintenance

 Share

Recommended Posts

ClutchBurndout-:( Grand Master

ClutchBurndout-:(

Posted
Posted

as the title says, when im stationary, when the car is cold (no issues when engine is warm) when the clutch is out not in gear, the idle is fine, but when i clutch in and engage first, while stile staying stationary, the revs drop about 50-100 rpm, what causes this? and its weird how it doesnt do this when the engine is warm.

any ideas?

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

At the top of the clutch pedal there is a small pushrod that gets pushed into the master cylinder. This rod can be adjusted as clutches wear out etc. Have a look at this push rod. U will need a light to see it. Then with ur hand see how much freeplay(travel without touching the mastercylinder) there is. If there is a bit, adjust the pushrod so it moves towards the master to remove most of the freeplay. Make sure there is still a tiny bit of freeplay or ur clutch will slip.

Doing this will act as if u are pushing the clutch pedal further. Which inturn disengages the clutch more and should fix the creeping issue u have

ClutchBurndout-:( Grand Master

ClutchBurndout-:(

Posted
  • Author
Posted

At the top of the clutch pedal there is a small pushrod that gets pushed into the master cylinder. This rod can be adjusted as clutches wear out etc. Have a look at this push rod. U will need a light to see it. Then with ur hand see how much freeplay(travel without touching the mastercylinder) there is. If there is a bit, adjust the pushrod so it moves towards the master to remove most of the freeplay. Make sure there is still a tiny bit of freeplay or ur clutch will slip.

Doing this will act as if u are pushing the clutch pedal further. Which inturn disengages the clutch more and should fix the creeping issue u have

cool, thanks mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      Ha ha ha! I know those feels mate I've finally got the garage cleared enough that next weekend I'll do some actual work on my car (hopefully). Unfortunately garage isn't usable after 10am at the moment That said, I've done a lot of work this weekend on helping finalise a friend's Production Race car. Full started Christmas Eve. We're down to about 8 tasks on the list, including "get a wheel alignment". Sometimes it's just easier working on someone else's car or project than our own stuff 😛
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Ha ha, ended up going it alone.  I just sent it (in a very nervous fashion).  Once I'd released the locks and it didn't automatically start spinning out of control i felt a bit more confident.   It made some loud sounds (cracking and creaking noises) when I first spun it which got the heart rate going again!  I couldn't bring myself to leave it tipped on the side.  I feel a bit more comfortable having back right side up while it sits there. I'd get angry with your last point but you're 100% correct! 😅 Even yesterday I managed to distract myself at numerous times to make a bracket to fit an LED flood light off the back of the house and fix my sons pushbike.  There were other little taks nibbling at my brain for the rest of the day too...
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Probably one of the more nerve wracking experiences of my entire life! 😂😂 The balance (centre of gravity) is out still but in a direction that gives me comfort!   It's quite bottom heavy still meaning it takes a bit of muscle to rotate it.  The plus side of that is that it wants to to go back to upright.  Better that than wanting to go all stranded turtle on me!
    • Duncan
      R32 GTST - 600KW+ RB28/CD009 Build

      By Duncan · Posted

      hmmm that's not ideal. This is a pretty new engine right, will be interesting if your engine guy has any theories about causes
    • TurboTapin
      Hicas ball joint install tool

      By TurboTapin · Posted

      A universal ball joint removal c press kit is better money spent and will work for the Hicas ball joints.  Here's a 45$ CAD Example. ATPEAM Heavy Duty Ball Joint Press Kit with 4WD Adapters | Professional 4 in 1 Ball Joint Press Removal and Installation Tool for Cars and Trucks | Universal Ball Joint Tool with Storage Case, Ball Joint & Tie Rod Tools - Amazon Canada
×
×
  • Create New...