Jump to content
SAU Community

Recommended Posts

  • Replies 184
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Was thinking of using that on the roof lining atleast

But main aim is to get it road worthy and engineered. which means getting this motor finished

Block was just dropped off at the machinists for an acid bath, all welsh plugs and gallery plugs are being removed. Then we'll check the piston to bore clerance to ensure the stock pistons are still fine in the bore

If not, i'll have to try the other 2 blocks i have

The 10mm foam won't fit in the roof, needs to be 5mm. I learnt this the hard way and it made the clips at the back near the rear window separate from the lining after a few days. I think I've got enough of the 5 mm left over at home. If I do it's yours.

Try out the foam I used on top of the dynamat Chris, weighs nothing and makes a big difference.......just my 2c

Whats the "foam" you refer too champ? Any pics to what you are talking about? :unsure:

Bit of progress :)

Always hated how unsecure the front bar was, dealing with bolts into the guards and spacers between the lights. This basically allowed alot of movement when driving leading to rattles etc.

As you can see below im working on a new reo for the bar, tied into the 8mm plate steel mounts for the intercooler.

So in order to secure the front bar in a way that allows for fairly easy removal i made up some mounting points that were attached to the front bar.

IMG_3281.jpg

Then triangulated some supports to hold it in place while i removed the bar

IMG_3282.jpg

Then once removed i linked them to the support bars.

IMG_3285.jpg

then reinstalled the bar to test it out

IMG_3286.jpg

PERFECT! so sturdy, and just with these 2 mounting points

IMG_3288.jpg

Next step is to connect the rear of the bar to another support, so this will remove the connection to the front guards.

So to hold it in place until i've finished the new mounts i use the panel clamps i got in my Cleco kit.

IMG_3287.jpg

Next step will be to work on the intercooler piping on the hot side.

Need to wait until i get some new rollers for my MIG so i can run 0.6mm wire to connect these 2 4inch stainless steel sections into the body work.

IMG_3213.jpg

IMG_3212.jpg

IMG_3211.jpg

I designed them this way as i was cutting through the silicon joiners as they passed through the factory holes, so angled how i need them for better pipework design and a CAI for the airbox i'll build later on.

With everything closed it was time to tackle some of a little jobs that i didnt need materials or tools for.

R34 GTR passenger seat mounts were modded by welding on the stock seats mounts back to the rails.

IMG_3297.jpg

IMG_3298.jpg

Also installed the new painted dash to get it back to a more stock look, removing the guage holes and will let me start working on the new guage holder in the DINN area.

IMG_3299.jpg

next for this area is to mod the gear shift around to hold the ID3 display, then paint it to match.

bottom dash pieces will have to stay out until the RB26 loom and ecu is ready to go in

Another little update, took a while to cut out the shape, but the new holder for the ID3 display is mostly ready.

Just need to work out a mounting option for it, and get some velcro to hold it in place..

IMG_3301.jpg

IMG_3302.jpg

IMG_3304.jpg

IMG_3305.jpg

IMG_3306.jpg

Bit more progress today before the work week starts again.

Triangulated up the front bar mounts with tubing, then to test out my new dimple dies we added the plating between the supports.

IMG_3307.jpg

IMG_3308.jpg

IMG_3309.jpg

IMG_3310.jpg

IMG_3312.jpg

IMG_3313.jpg

Next step is to finish welding the supports, then make a new support panel for the new power steering fluid cooler.

I will be working on getting the car running again with the RB25 to test out the all the changes already made to : brakes, fuel system, wiring, intercooler, front bar supports, rear suspension geometry, and the new Tein Flex's i installed earlier (these need to be leveled out after the settling period)

so plenty of things to go yet, but getting close to running again. Dont want to jump too far ahead and have alot of things to tweak when the 26/30 goes in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
    • Excuse me, but 2) does apply 1) Would also apply if you consider how much is spent in the alternatives. Also there's the option of 3), buy one pre-built that you can put your family in (it's me, it's my car)   That said, I went on a ~500km drive the other day. I didn't use anything more adventurous than 3rd/4th gear at about ~3000RPM and 50% throttle and I was going as fast as anyone has any sense doing on a public road, with enough grip to the point where I didn't want to go any faster. I was obviously under the limit of the current car etc etc. MX5 with 2.5 N/A to achieve the same speed would be more fun for any road scenario. Maybe consider cams. I wouldn't boost it. The use case is just not there and it won't actually make the car more enjoyable unless you really do plan on wringing gears from 1st to 3rd (at least) at 100% WOT on a public road to 150+kmh.
    • Great if: 1. You had all of the money for everything else that is required  2. Lived in a country where you could actually do this and drive it legally on the road Sadly, neither applies to me As for the turbo, I am having second thoughts, mainly for engineering/registration legality reasons and insurance  Not saying I've finished doing stupid things that I probably should do to the MX5, but boost, and V8 engine swaps isn't on the cards Strange, but true 
×
×
  • Create New...