Jump to content
SAU Community

M35 Banjo Restrictor

scotty nm35
 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

I have moved the discussion off the Dyno results thread.

We have been recommended to drill out our turbo oil restrictors to 3mm once going to a bushed core highflow, I only found this out after Aaron's failure. I have been running the stock 1.2ish mm restrictor with my old turbo for well over a year and the shaft play is fine so I doubted the info but every turbo swap I have done now has included the drilling of this banjo to 3mm.

I dont think the BB cores require it but Aarons core failed almost straight away. I can only assume the reason his stock turbo and then his BB highflow failed was from gunk blocked in the hole. (it was very mucky inside the banjo when I drilled it out.)

I am still running the stock restrictor in mine as I have gone back to the stock turbo temporarily. My restrictor was clean inside but I recently flushed it and I have always changed my oil before 5k. Perhaps it is slack servicing while in Japan that causes the block to dirty up?

Link to comment
https://www.sau.com.au/forums/topic/358131-m35-banjo-restrictor/
Share on other sites
Commsman Veteran

Commsman

Posted
Posted

Great info, thanks Scott.

Like you say, it may just be that the stock turbo can handle more boost if they get the proper supply of oil. I'll be checking for any gunk in mine ASAP.

scotty nm35 Grand Master

scotty nm35

Posted
  • Author
Posted

Its only a theory, and it will definitely shorten it life still. I say to anyone buying an M35 to keep some cash aside for what will eventually happen.

If I can save one person's turbo though, by explaining this oil issue, i'm a happy man. :)

Sunkist Grand Master

Sunkist

Posted
Posted

it will shorten the life, i ran my stocky at 20 psi and it took just under 6 months to blow up.

but who knows whether it was being starved, i'de say the BB core was, it make a loud whining noise from the word go.

but the stock turbo's power was very impressive!

Sage222 Rising Star

Sage222

Posted
Posted (edited)

you ran 20psi for 6 months with a factory turbo?? and other mods to help support it?

hmm.. maybe ill add a couple more psi! :)

how hard is it to drill out the restrictor? would you recommend it for a standard turbo setup?

Edited by Sage222
scotty nm35 Grand Master

scotty nm35

Posted
  • Author
Posted

lol, wait till I have worked out the Garrett install just in case. >_<

The stock turbo shouldn't need any more flow, would it hurt? Im not sure, I dont think it would damage anything, if there is too much flow it may get past the seals and burn in the dump. Its not too hard to get the banjo bolt out, and easy to drill in my lathe but it can be a pain to line the banjo back up to get it all back together and if the bolt isnt straight it will munch the thread. (cast alloy sump)

The stock setup will run out of injector fairly early, if you plan to bump it up, get some way of adjusting the mixture and timing. (Emanage) You will make a much greater gain then.

Sunkist Grand Master

Sunkist

Posted
Posted

you ran 20psi for 6 months with a factory turbo?? and other mods to help support it?

hmm.. maybe ill add a couple more psi! :)

how hard is it to drill out the restrictor? would you recommend it for a standard turbo setup?

yeh as scott said. it probably isnt advisable, i was just a young p plater then and all i wanted was boost and a loud PSSHHH sound.. ive grown up now..

lol

i didnt realise i wouldve maxed my injectors duty cycle, and probably considered myself lucky i didnt break things(more than the turbo)

i probably wouldnt drill out the restrictor, incase you need to go back for whatever reason, or drill it out to much..

im happy with my set up now, i just want to run lower boost now, but cant with the wastegate size being a tad bit too small - didnt realize 1-2mm of wastegate, would make such a difference.

Jetwreck Grand Master

Jetwreck

Posted
Posted (edited)

yeh as scott said. it probably isnt advisable, i was just a young p plater then and all i wanted was boost and a loud PSSHHH sound.. ive grown up now..

lol rofl.gifrofl.gifrofl.gifrofl.gif

i didnt realise i wouldve maxed my injectors duty cycle, and probably considered myself lucky i didnt break things(more than the turbo)

i probably wouldnt drill out the restrictor, incase you need to go back for whatever reason, or drill it out to much..

im happy with my set up now, i just want to run lower boost now, but cant with the wastegate size being a tad bit too small - didnt realize 1-2mm of wastegate, would make such a difference.

I'm surprised your turbo builder didn't think of that since his not just a machinist! :P on a more serious note...I'm surprised your turbo builder didn't think of that

P.S. You might want to add "running E85" in your signature! :P

Edited by Jetwreck
  • 4 weeks later...
whiteaxis Explorer

whiteaxis

Posted
Posted

I'd really like to check out the banjo restrictor as the whining has been getting louder from my turbo (the whining has been getting louder from the passenger seat since the new exhaust aswell but that's a different story......)

I've read that the restrictor is on the block but where is it exactly? Should I approach it from the top or from underneath?

Hopefully checking this and doing a flush will extend the life of my turbo a little.

Sunkist Grand Master

Sunkist

Posted
Posted

I'd really like to check out the banjo restrictor as the whining has been getting louder from my turbo (the whining has been getting louder from the passenger seat since the new exhaust aswell but that's a different story......)

I've read that the restrictor is on the block but where is it exactly? Should I approach it from the top or from underneath?

Hopefully checking this and doing a flush will extend the life of my turbo a little.

theres two bolts. one to the turbo, and one on the engine sump or block.. find the line on the turbo and trail this to the block.

the banjo on the block has the restrictor and will need to be checked.

im thinking it was the cause of mine blowing up the 2nd time. If you can save it, thats a plus.

scotty nm35 Grand Master

scotty nm35

Posted
  • Author
Posted

Once its whining the bearings are shagged so its only a matter of time before the rear wheel contacts the housing and smashes itself to pieces unfortunately. You may get a few more months out of it, perhaps a lot more if you drive conservatively. (Yeh right. :))

  • 7 months later...
FHF Enthusiast

FHF

Posted
Posted

I'm getting myself prepared to drill a bigger hole 1.5 - 2mm and I just wanted to find out the correct procedure for this...

Would it be ok to use a table vice and a cordless drill ?

It would be appreciated if someone could give me detailed information in how to drill this hole.....

thanks in advance...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kyer32
      Want to buy a Rb20det preferably in Sydney

      By Kyer32 · Posted

      Hey guys I’m chasing a Rb20det complete or bare block need a good running engine as mine has low comp 
    • GTSBoy
      HY51 Fuga Hybrid

      By GTSBoy · Posted

      You're making my point for me. 95 is not "premium". It is a "slightly higher octane" version of the basic 91 product. The premium product that they want people to buy (for all the venal corporate reasons of making more profit, and all the possibly specious reasons of it being a "better" fuel with nicer additive packages) is the 98 octane stuff. 95 is the classic middle child. No-one wants it. No-one cares about it. It is just there, occupying a space in the product hierarchy.
    • sonicii
      HY51 Fuga Hybrid

      By sonicii · Posted

      98 and 95 have to meet the same national fuel standards beside the actual RON.  91 has lower standards (which are quite poor really), so 95 is certainly not 91 with some octane booster. It would be an easier argument to claim 98 is just 95 with some octane boosters. Also RON doesn't specify 'quality' in any sense, only the octane number.  Anything different retailers decide or not decide to add to their 95 or 98 is arbitrary and not defined by the RON figure.
    • silviaz
      Shitty Series 1 R34 Interior Plastic Paint

      By silviaz · Posted

      Anyone know alternatives to powerplus tungsten? Can't find an alternative online. 
    • GTSBoy
      HY51 Fuga Hybrid

      By GTSBoy · Posted

      95 is just a scam outright. 98 is the real "premium" with all the best detergents and other additive packages, and at least historically, used to be more dense also. 95 is just 91 bargain basement shit with a little extra octane rating. Of course, there's 91 and there's 91 also. I always (back in the 90s early 2000s) refused to put fuel in from supermarket related fuel chains on the basis that it was nasty half arsed shit imported from Indonesia. Nowadays, I suspect that there is little difference between the nasty half-arsed shit brought in by the "bargain" chains and the nasty half-arsed shit brought in by the big brands, given that most of it is coming from the same SEAsian refineries. Anyway - if there's still anything to that logic, then it would apply to 95 also. 98 is only made in decent refineries and, as I said, is usually the "premium" fuel, both in terms of octane rating and "use this because it's good for your engine because it's got the unicorn jizz in it!".
×
×
  • Create New...