Jump to content
SAU Community

Recommended Posts

  • Replies 804
  • Created
  • Last Reply

Top Posters In This Topic

yes you would.

When i put a gen GTR bar on my 32 sedan, i used the R reo (cause i was told i needed to, and the bar i bought came with it)

The only thing you'll notice when putting a genuine R bar on is that the sides buldge out a bit, due to the gtst being not as wide as the R.

Hope that helps. (someone correct me if i'm wrong.

depends who you ask! some say yes and some say no, try thegtr bar on the gts-t reo before you buy

I dunno about that lol, I see masses of R32's everyday gettin around my area. Very close to the same amount of 33's I see. They are all common but I still think 34's are the least common, especially coupes. Do see a fair few 34 sedans.

must be an area thing, naff all 32s in midland ,altho there is a nice n tidy 32 sedan up the road on great northern hwy

finally finished my repairs from the hail storm.... personally i think it's looking even better than before it got all dented.

thats f**king hawwt dude, rims suit it so well. always loved black 32s, but gunmetal has to suffice lol

Pulled the fans and intercooler/piping off yesterday. Degreased + highpressured the piping/cooler and the engine bay then cleaned the cooler core out with some thinners.

This afternoon the cooler/piping and fans will go back on and probably trim the front bar and bolt that up too.

Radiator was ordered yesterday :banana:

Clutch was inspected and deemed to need an overhaul kit.. ~$650 for the kit but not available until next month!! So looks like I'm going to grab a new Exedy button clutch instead.

Ordered my tensioners and idler this morning from Statewide Bearings, NSK part numbers, VERY reasonable prices!

The only unknown at the moment is injectors... anyone got some GTR injectors for about $100?:P

Fans back on, cooler on and plumbed up.

HID's wired but only one fitted because my drill went flat fkn (typing this while I wait for it to charge)... what a cnt of a job, the retainers in the wagon would have been perfect but the retainers in the 32 required some "modification".

Bonnet latch & support back on and operating well.

Need to pull the reo off and give it a bit of a grind tomorrow, the dodgy hacking from the previous owner fouls the cooler in one spot :(

Oh and a successful NIStune fitting today on a 34GTT, drive in drive out :D

Ok lets see if this drill has enough charge fkn

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • find it funny everyone claims different fuel chains, do different things with their fuel blah blah blah. We don't have that many fuel terminals in Australia. The fuel tanker trucks drive into the terminal, fill up, and drive directly to the service station and dump out. The majority of fuel you get, is coming out of the same terminals. The variation is actually at the individual service stations and how good their tanks are, as well as how much turn over they actually have. Older fuel stations, that haven't had their tanks replaced are going to end up with the worst fuel. Also a lot of older stations have shit design, and shit maintenance, and end up with more water absorption into the tank. This is when you then get a bad batch of fuel. Other shit things happen, like tanker drivers have a f**k up, and starting to unload the wrong compartment on their truck into the wrong tank. 
    • This one?? In other news: I cannot tell the difference between my red MX5 with the silver grey hard top......... and the Ferrari 599XX EVO, they might as well be twins, well.......apart from the big wang hanging off the back of the Ferrari...🤔🤣, without the wing they are identical   
    • Turn it into the pride flag 
    • I think you'll find we're confused about what you were trying to do and how you were doing it. I would have thought that block rigidity was something you measured while loading the block in beam or in torsion, and that you would do so before and after grout filling, to see if putting material in there created a "composite" construction with the expected rigidity increase. Notwithstanding that the true function of grout is less about gross rigidity than local (ie preventing bore deflection/splitting and tying the bores to the main bearing locations a little better, etc etc). It is nearly impossible to follow your description of what you've done without closing ones eyes and making "aliens" hand shapes in front of oneself to try to follow the manipulations you've made. It's still unclear to me what you were trying to prove.
×
×
  • Create New...