Jump to content
SAU Community

Gtr Modification

lav

By lav,
in Victoria

 Share

Recommended Posts

lav Community Regular

lav

Posted
Posted

i have standard rb26dett engine on gtr33 with bleed valve, power fc, adj cams, high flow 3 3/4' exhaust and just got a pair of -9's from Osaka Imports today for $1500

Just wondering what kW am i looking at once the turbo's and dump pipes are installed....

and how much without the dump pipes.....

been told that by installing dump pipes, it makes a difference....

need to know what other supporting minor mods can help to increase the power......

thanks guys :)

Link to comment
https://www.sau.com.au/forums/topic/359207-gtr-modification/
Share on other sites
Ant97GTR Grand Master

Ant97GTR

Posted
Posted
have standard rb26dett engine

Your first concern should be reliability and power being well and truely second. Once all bolted together get a good tuner to sort out a reliable tune.

As for the dump pipe difference, I guess it depends which dumps you have bought - sure they can make a difference but by how much depends on how good they are.

CR34M Community Regular

CR34M

Posted
Posted

280AwKw would be safe, look upwards of 320AwKw but less reliable, depends how the car is tuned and where the power comes on....no point having 320 when your power is upward of 8000rpm for eg. 280-290 would be suffice with the set up and parts you have.

lav Community Regular

lav

Posted
  • Author
Posted

280AwKw would be safe, look upwards of 320AwKw but less reliable, depends how the car is tuned and where the power comes on....no point having 320 when your power is upward of 8000rpm for eg. 280-290 would be suffice with the set up and parts you have.

Yeah, im looking around 300 mark atleast....will see once it go on the tune....

  • 2 weeks later...
lav Community Regular

lav

Posted
  • Author
Posted

I definately agree with Ant97GTR though, there is a big difference in making big power and making it and still keeping the reliability, take to a tuner who knows these cars inside out!

Where did you take yours to?

Many people told me that with the -9 on stock motor will be around 280 to 300 kW

I wonder how urs made 300+!!!

very concern and will like to know if you did anything else to yours....

Fullboost_Performance Apprentice

Fullboost_Performance

Posted
Posted

Where did you take yours to?

Many people told me that with the -9 on stock motor will be around 280 to 300 kW

I wonder how urs made 300+!!!

very concern and will like to know if you did anything else to yours....

Mine had a built engine, head work, cams, cam gears, 4" exh from front pipe back.

I have seen same setups making 290, friend of mine in his R32 GTR is making 328 with more boost, was tuned from a place in NSW just before he bought it, so i would say a little more boost and head work makes the difference.

Simon from NT Performance Turbocharging in Footscray, they had built some pretty serious GTR's and GTS-T's thats why i took mine there, if your keen i can pass their number on and you can have a chat to them about what was done.

I dare say that yours with head work perhaps a slightly bigger exhaust would make more

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
    • kevboost7
      Magnetic Drain Plug Snapped in Half

      By kevboost7 · Posted

      F my life. I was changing the oil on my R32 GTR today as usual and ran into a bit of a snag. I drained the oil out and was getting ready to finish the job by tightening the drain plug, however The stupid magnetic oil drain plug snapped in half, right at the magnet part. After about an hour of trying to remove it, I used a drill bit, which unfortunately pushed the magnet all the way into the pan, and just leaving the hollow threaded part of the bolt remaining. I was able to remove the hollow portion of the bolt from the oil pan with some pliers but the magnet is still in there.  So, the question is, should I drop the oil pan to get the magnet piece out, or is it okay to leave it in there? I really dont want to drop the pan, i'm about to go nuts.  PSA: Do NOT buy a BLOX magnetic drain plug. This is the one i had.    https://bloxracing.com/products/magnetic-oil-drain-plug-m12x1-25mm?variant=37131252859052&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gad_source=1&gclid=CjwKCAjw47i_BhBTEiwAaJfPpgti1D2JwO7TDuMpXuqeQPCuIQSAfwxpWQH5rF9MD7sm5SCZDWLR_RoC_YoQAvD_BwE    
×
×
  • Create New...