Jump to content
SAU Community

Recommended Posts

Things already gone :

motor

gearbox + manual conversion parts

all looms

dash pad

dash facia

rear end complete (ie brakes, diff etc all spoken for)

front brakes

drivers window switch is broken

==========================================================================

AVAILABLE PARTS:

boot $100

door r/h $100

door l/h $100

mirror $50

mirror $50

seats $50

wheels $300 stock but with almost new tyres

door trim l/h $50

door trim r/h $50

centre console $50

factory shocks $100

power steering rack $110

air con compressor $250

power steering pump $150

Nismo FPR $80

HKS Turbo Timer $50

drivers guard $80

dash cluster - 155443km $80

Bunch other stuff available like brake booster/master etc small brackets tail lights

drivers side trim has some funky pads on it design to fit in the spaces where your knees go on track days when you have stock seats.

IMG_3254.jpg

IMG_3253.jpg

IMG_3252.jpg

IMG_3250.jpg

any questions ask away

Located at Penrith, NSW and would prefer pickup as i dont get much time to go to post offices.

Link to comment
https://www.sau.com.au/forums/topic/359885-wrecking-r33-gtst-white/
Share on other sites

  • 2 weeks later...

Is that piece of cooler piping that I can see still there? I'll take it for $5, I can use it for something. PM me, I'm near parramatta so might have to come west.

The cooler piping was all mandrel stainless, its been put aside for a N/A project i'll be working on soon, sorry

interested in the rear pods are they still avalible?

cheers nick

pods are still available, they are stuck on pretty well so i'll take them off and take some better photos for you, just incase i damage then taking them off

Do you have the front lower control arms? Price?

They are still there, though as you can see the was a fair amount of movement on that passenger chassis rail, i'll take if off next week and make sure they arent damaged first.

They are still there, though as you can see the was a fair amount of movement on that passenger chassis rail, i'll take if off next week and make sure they arent damaged first.

Great thanks.

  • 4 months later...

Reviving this thread now i had some time to start stripping it again.

Still AVAILABLE PARTS:

boot $70

door r/h $80

mirror $20

mirror $20

wheels $300 stock but with almost new tyres

door trim l/h $50

door trim r/h $50

centre console with lid $50

factory shocks and springs $100

power steering rack $110

air con compressor $250

power steering pump $150

Nismo FPR $80

HKS Turbo Timer $50

drivers front guard $80

dash cluster - 155443km $80

Found - adjustable poly bush caster rods : $80

Russ: lower control arms are fine from my measurements if you are still keen $150pr

Keen to get this car out of my shop so make some offers.

Cheers

Chris

how much for the rear pods and side skirts?do u have a front bumper to?

no front bumper sorry, sides skirts are useless as there is only one.

i'll see if i can get the pods off today,lots of glue on them, but they will be cheap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 馃槕. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
  • Create New...