Jump to content
SAU Community

Recommended Posts

I think if you look at the bottom end it's clear.

You might also read the tea leaves on the rb26 vs. 2jz because you'll come to the same conclusion.

But like Holdens and Fords, you choose your sides and you live with it and it'll be a cold day in hell before I own a Soarer or Supra.

T.

Then again when you can get gtr stuff and poke it straight into the 25 it adds a different aspect to the equation. Yes I realise you are talking stock but the rod upgrade is cheap and easy.

If anything, my only detraction from the 25 is the ease with which you can overboost the engine and the resulting detonation kills the pistons.

End of the day, horses for courses...and this is a skyline forum so bugger off with yer toyo crap (yes my soarer alternator died today so I'm off toyo)

i think they both sound amazing in their own separate ways, and both have their own better/worse characteristics

id go with this comment...there is a write up in zoom comparing the 1J to the rb26 look it up and read it i dont want to sound bias...

the RB25 is a fantastic engine but as far as 1J vs rb25 no offence but the 1J is better compared to the rb26...

I wouldn't say the 1JZ is better than the RB26, but it certainly is in a class beyond the RB25.

Daresay the reason you don't commonly see serious example of 1JZ is due to the vehicles they were released in (Soarer, MKIII Supra).

The update single turbo VVTi 1JZ is where it is at

The 1JZ might be a "class beyond" the RB25, but I daresay that the rest of the car (R32+ Skyline) is a "class beyond" any comparable Toyota. What do you buy a car for anyway, the strength of the bottom end? You can change that easily. But you can't change fatass porky styling. My "inferior" RB25 is pumping out 220+ at the wheels and I see any point in comparing it to other engines that are capable of holding more power. My engine does the job and that's all that matters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've watched some vids and the technique seems to be to butt the sheets up to one another and use MIG to spot weld and slowly fill in the spots until its eventually all sealed. No runs as you would normally do, as there's too much heat generated that way. Yeah my stick welds are terrible these days because its been so long since i've done any of it. I expect to be spending many hours practicing
    • I have personally seen a Tomei USA RB26 cam that didn't even fit the head. Kind of nuts to me that it was even possible for that to happen but such is life.  There's two UP Garages in the US. One is a US branch of the Japanese company which sells things they brought over at tremendous markup. The other is University Place Garage/Fairlady Motors which is a shop best known for putting VCAM in RBs and trying to convince people to stop putting in 800hp of turbo on a 2.5L motor.
    • Gasless MIG is not exactly suited to what I would call "delicate" or "attractive" welding. So I would rule it out for sheet metal rust repair type stuff, unless you're only doing it in hidden places. I'm thinking about getting myself a gasless MIG for "hack together" type work. Noting that my welding experience is very very low, and quite a long time ago. So I'm also looking for "simple", but I'm not expecting "excellent". I'm not even sure that proper MIG is the best for sheet metal work. I get the feeling that the degree of control and the minimisation of heat input that you get from TIG is probably what you really want. And then you have to get good at doing it before the welds won't look like a monkey flinging a handful of shit anyway. You're probably SOL for an easy and cheap way to get from where you are to where you want to be. Much like myself.
    • Any recommendations for what would be the easiest welding type to start on, for sheet metal rust repairs and maybe some exhaust piping too? Seems like MIG is the most common. Would gasless MIG be ok to learn on and do some simple jobs? I have a stick welder which has a Lift TIG setting, but i'm more interested in getting whatever's easiest to do, and most suitable, rather than using what i have.
    • Is the UP Garage in the US of Ayyeee even the real UP Garage?
×
×
  • Create New...