Jump to content
SAU Community

Heat Shield Over Turbo

Jmans GTS-T

By Jmans GTS-T,
in General Maintenance

 Share

Recommended Posts

Luciano Veteran

Luciano

Posted
Posted

Is there any cons to not having a heat shield over your turbo on a R33 Skyline? as I am thinking of leaving it off...

My cousin runs his without it, doesn't seem to have any problems. Just be careful there isn't any obstructing items/bits around the exhaust side of the turbo though, you don't want anything to burn.

The other small nuisance is everything around the turbo gets a lot hotter - when we were working under the bonnet (particularly on that side of the engine) after taking the car for a test drive, we'd just have to wait for things to cool down.

Munkyb0y Grand Master

Munkyb0y

Posted
Posted

Basically you will just increase engine bay temperatures, which is a downside. Leave it on if you can.

Or if you really hate the look of it make one yourself that looks better - I did.

can we see the one you made? :)

what material did you use?

Jmans GTS-T Enthusiast

Jmans GTS-T

Posted
  • Author
Posted

I used fairly thick stainless steel to try and isolate the heat. I also made it go down as far as possible down the side of the turbo.

Not the best picture but you get the idea.

post-35676-0-23224200-1302518226_thumb.jpg

That whole engine bay looks awsome!!! good work man!!! and cheers for the heat shield idea, that looks great!

turael Enthusiast

turael

Posted
Posted

Nice heatshield!

If the car sees hard work (track days, drift, burnouts), you really want to consider leaving the heatshield on or making a baller heatshield like Phil

Mate of mine had his car catch fire under the bonnet due to no heatshield after ripping a burnout at Powercruise.

Also in the drift cars with no shield you can sometimes see issues with the paint on the bonnet over the turbs

Munkyb0y Grand Master

Munkyb0y

Posted
Posted

i'm thinking, as good as it looks, is stainless good as a heat shield though? doesnt it get crazy hot itself?

what about aluminium?

or this stuff? its very shapeable. ceramic sandwiched between aluminised steel sheets?

P1310006.jpg

PM-R33 Grand Master

PM-R33

Posted
Posted

Yep that stuff above is a lot better as an insulator.

As regards to aluminium I don't think it would insulate heat any better and may start to melt or burn if fairly thin (from memory aluminium has a much, much lower melting point).

My setup is definetely not the best heatshield you can make, but easily noticable difference of under bonnet temps with it on or off (have had it on and off heaps of times in the past).

Like I said, mine was mainly for looks and to atleast have some sort of shielding in that area.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Magnetic Drain Plug Snapped in Half

      By GTSBoy · Posted

      She swallowed the spider to catch the fly.
    • soviet_merlin
      Magnetic Drain Plug Snapped in Half

      By soviet_merlin · Posted

      Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
×
×
  • Create New...